Models > 12-1063-00-05 > Instructions

12-1063-00-05 Tappan Range - Instructions

All installation instructions for 12-1063-00-05 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 12-1063-00-05
151-165 of 170
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

oven took very long time to ignite.

  • Customer: Ronald from Keymar MD
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
first we went online to see if others had experienced the same problem, and what they did to fix it. ordered part to arrive within three days. husband removed connecters from old igniter and spliced them onto new one. We felt it should have come with connecters. set burner with new igniter in place, and it worked...Yay! just in time for Thanksgiving turkey!

Igniter glowed but slow or no oven lighting

  • Customer: JAMES from Harrison MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced the igniter.

oven wouldn't light

  • Customer: Donna from Trinidad CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
using socket set removed old ignitor,replace with new one and secured using the socket set. The oven lite right up.Service was A1. I ordered on Friday evening and the part was delivered on Monday. Thank you.

Oven would not light

  • Customer: Edward from Pent Water MI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Put a new ignighter in the oven I also would like to commend PartSelect for the fast service on the part i ordered it one day and recieved the part the nexted day i would recommend you any time

Oven lights intermittently, smell of gas

  • Customer: Robert from Lakewood NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Model# GLGF366ASD range
Turned off breaker
Removed oven door (see gas range manual for procedure)
Removed storage drawer on bottom of range.
Removed oven racks.
Removed oven bottom panel (2 screws in back of panel)
Removed oven shield (screw on left and right front of panel & nut in middle of panel)
At this point igniter was exposed
Removed igniter by removing the 2 self tapping screws securing igniter.
Note: threads on both screws stripped during removal, requiring both
screws to be cut off for removal.The stripping of threads of these screws
is probably normal due to the heating and cooling of the oven during
operation, making the threads on the screws brittle.
Marked the top wire on the igniter with a black sharpie
Cut both wires as close to the old igniter as possible.
Cut wires on new igniter about 10" long.
Connected new igniter with wire nuts (provided) making sure to connect wire from top of igniter to wire marked with sharpie.
Installed new igniter using 2 new #8x1/2" self tapping screws.
Pulled excess wire & wire nut connections down into the back of the storage drawer area making sure wires were resting on flanged area of panel.
Reinstalled oven shield, panel, racks, storage drawer, and oven door.
Turned breaker back on.
Oven works great.
Note: self tapping screws should be provided

Igniter not drawing enough volts to open safety valve.

  • Customer: Christopher from Oakmont PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the oven drip pan and removed the old igniter and cut wires and used the supplied wire nuts and replaced the old part turned the oven on and it ignited.

Gas oven light off time long, strong gas smell in house from long light off time. Oven would not control desired temperature.

  • Customer: Richard from Rockford IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Disconnected electric power. Removed oven floor and flame spreader to access igniter. Spliced replacement igniter to original igniter connector plug wires. Mounted new igniter and reinstalled flame spreader and oven floor. Reconnected electric power and checked oven operation. Oven light off time was within 1 minute and oven temperature controlled to all settings up to 450 degres.

Oven took a long time to light, did not stay lit

  • Customer: Carol from Campus IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Very Easy. Part arrived in less than 48 hours of ordering. Followed the directions included with part and referenced the information posted here.I have no mechanical talent and was able to install the part without difficulty.

Gas oven would not light

  • Customer: Steve from Fredericksburg VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I checked the igniter resistance with an ohm meter. It read about 350 ohms. Voltage across igniter leads with igniter removed was 120 volts when the oven temperature control was turned on, so I knew the gas control and thermostat were ok. The new igniter has a resistance of about 220 ohms, so the difference was apparently enough to keep the oven from turning on. This is the second igniter I've replaced in this 20 year old oven, the first bad igniter had open resistance, obviously since it was visibly cracked. The repair went very fast, directions were great.

would glow but would not ignite

  • Customer: charles from Mount Prospect IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Turned off power removed racks removed bottom panel removed flame distribution plate removed igniter i didn't use -the wire nuts 'the wires on the new part were more than long enough so i installed new stake ons reveresd disassembly process turned power back on and now it works great with a factory look

no flame on broiler or oven

  • Customer: david from coalinga CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
replaced the ignitor switch, umplug oven turn off gas. removed racks unscrewed two screws in back of oven (inside of oven), removed bottom piece of oven, one screw for broiler cover removed, then two screws for ignitor, cut wires peeled off some excess covering, twisted the new ignitor to wires covered with attached cap tightly replaced two screws in ignitior, replaced one screw in broiler cover, two screws for bottom cover, replaced racks, pluged in turned gas and turned on stove ignitor lit up and started oven broiler, now i can cook again.

oven would not ignite

  • Customer: Diane from Southbridge MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
the gas control valve was removed ,then the igniter. The new part was plugged in and the valve was applied. It started right away. I want to thank the sales man, he sold us just what we wanted, not the one we thought we needed which was 240.00. My repairs cost $42. and a meal for my son and a friend. Would reuse this service again if needed.

Oven heated slowly, then not at all.

  • Customer: Gregg from Roseburg OR
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
1. First, I read other people's instructions on this site, and that helped quite a bit. My own model was attached somewhat differently, so I was unable to replace the igniter in the same fashion as others. 2. Turned off the power to the oven after having done the non-electrical work: removed cover plate from bottom of inside oven (two screws in the back) to expose the igniter, and the heat shield from underneath the oven once the oven drawer was removed. Old, old screws so that was a bit of rolling around on the floor. 3. After that it was fairly easy: turned off the breaker, snipped one igniter wire from a plastic harness assembly under the oven and the other from the electrical core underneath the oven which was attached with a clamp. 4. Removed two screws to release the igniter. Now I could work on it in the light. Stripped the old wire underneath the oven, attached the old clamp to the other new wire, and then clamped one wire on and joined the other to the plastic harness wire with the screw cap. It was a bit of effort merely to get at things, but not difficult. Breaker back on, and the oven now works perfectly.

Igniter was past-due for a change-out!

  • Customer: Kevin P. from Chanute KS
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Just opened up the oven and went to work. Really easy repair. Removed floor of oven with two thumb screws. Removed flame diverter plate from burner with one screw. Removed igniter with two screws. Marked top wire, then untwisted old wire nuts to remove the old igniter. Replaced with new igniter and used enclosed new wire nuts. Reassembly was simply the reverse of above. Only issue - I needed longer arms to comfortably reach back into the oven!

oven not heating

  • Customer: Mickey A from Linden MI
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Oven ignitor glowing but no flame . Tested ignitor w/ ohm meter reading 2.5ohms , should be 3.3 or higher to allow gas flow . Ordered new ignitor , replaces and jackpot !! Oven now fires and heats like new . Thanks for part . Cost , $50 instead of $150 .
All Instructions for the 12-1063-00-05
151-165 of 170