Models
>
1109875279A
1109875279A Kenmore Washer Dryer Combo - Overview
Sections of the 1109875279A
[Viewing 17 of 17]
Keep searches simple, eg. "belt" or "pump".
Water Inlet Valve with Mounting Bracket
PartSelect #: PS334646
Manufacturer #: 285805
The water inlet valve on your washing machine is used to fill the tub with cold, warm, or hot water for the wash and rinse cycles. This part could have either a blue or green-colored valve body. There...
$35.28
In Stock
Door Catch Kit
PartSelect #: PS2162263
Manufacturer #: LA-1003
This door catch kit is designed for use in dryers. This is an authentic OEM replacement part. This catch assembly ensures the door of your appliance will close, and remain closed. It allows your appli...
$32.34
In Stock
Hose Clamp
PartSelect #: PS11743008
Manufacturer #: WP596669
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
$11.80
In Stock
Door Catch
PartSelect #: PS11741434
Manufacturer #: WP3389441
This white female door catch is attached to the dryer door.
$9.76
In Stock
Single Front Panel Cip
PartSelect #: PS11731288
Manufacturer #: W10854425
This part is the replacement single front panel clip for your dryer. It is made of metal and is approximately 2 inches long and ¾ inch wide. The front panel retainer clip is what holds the front panel...
$16.46
In Stock
Hose Clamp
PartSelect #: PS11740613
Manufacturer #: WP285655
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installat...
$11.10
In Stock
Lid Hinge Mounting Screw
PartSelect #: PS11748588
Manufacturer #: WPW10119828
Sold individually. NOTE: The color on the screw may not be the same as the image, but will still function the same.
$11.80
In Stock
Lid Strike
PartSelect #: PS11741871
Manufacturer #: WP358684
This part is used to activate the lid switch when the lid opens/closes.
$11.06
In Stock
Gearcase
PartSelect #: PS341974
Manufacturer #: 3360629
This is used in your direct drive washer that has a neutral drain.
$379.68
In Stock
Lid Bumper
PartSelect #: PS11747040
Manufacturer #: WP9724509
This gray and white washer lid bumper contains a rubber bottom and is sold individually.
$7.95
In Stock
Lid Switch Kit
PartSelect #: PS11741201
Manufacturer #: WP3355806
The pin on the lid pushes on the lever of the lid switch to tell the machine that the lid is closed.
$52.56
In Stock
Spin Pinion Seal
PartSelect #: PS11741857
Manufacturer #: WP356427
This seal is for the top of basket drive tube shaft.
$11.14
In Stock
Questions And Answers for 1109875279A
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the 1109875279A
[Viewing 12 of 12]Leaking
Fixed by
these parts
these parts
Show All
No hot or cold water
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
Will not drain
Fixed by
these parts
these parts
Show All
Noisy
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Will not agitate
Fixed by
these parts
these parts
Show All
Water Filling Issues
Fixed by
these parts
these parts
Show All
Burning smell
Fixed by
these parts
these parts
Show All
Door Pops Open
Fixed by
these parts
these parts
Show All
Lid or door won’t close
Fixed by
these parts
these parts
Show All
Spins slowly
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
washing machine is slow to fill with cold water
My washing machine became slower and slower to fill over the past several months. It also made a loud squeeling noise during fill-up (all this was on the cold water side only). I removed the old water inlet valve and tore it down, expecting to find corrosion or trash that was blocking the valve from opening completely. Turned out to th
... Read more
at the rubber diaphragm / seal was permanently "kinked", making it difficult to open the valve. The hot water seal was fine, but to make sure, I swapped them and re-assembled the washer. Now the problem was with the hot water, confirming what I thought. I ordered a new water inlet valve on Monday night and received it Wednesday! Installed it within 30 minutes and it works perfectly now. I am very pleased with PartSelect.com. I will definitely be a repeat customer, but hopefully it won't be anytime soon. ;)
Read less
Parts Used:
-
Roy from Nash, TX
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
274 of 298 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Cold Water would not shut-off
To discover what the problem was, I intially tested the inlet valve by blowing into both sides - discovering that the cold side was stuck in the open position. The hardest part was removing the back of the machine. First, you unscrew the top plastic part which contains the controllers by phillips head on either side. Then you pop the c
... Read more
lips out with a large slot screwdriver, then at the bottom, a nutdriver or large slot screwdriver there are two nuts to remove. The valve itself took a small nutdriver and pliers to remove the hose. Took less than 20 mintues to complete repair. Washing works like new now.
Read less
Parts Used:
-
Wendy from Dunlap, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
104 of 117 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The washer would not stop filling.
I took everything apart and put in the new inlet valve. Tried to run the washer and it was still not stopping when filling. I looked more into it and the tube that comes up from the wash basin to the load size selector switch was disconnected and that was the real problem. If this happens to you, I suggest first looking under the contr
... Read more
ol panel at the clear tube and ensuring that it is connected to the switch. Then if that is connected it is probably the inlet valve. There are helpful installation videos that can be found on the part select website that I would recommend looking at before taking things apart because it will make it much easier.
Read less
Parts Used:
-
Clay from Laramie, WY
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers, Wrench set
101 of 108 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!