Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 11084832201 > Instructions

11084832201 Kenmore Washer Dryer Combo - Instructions

All installation instructions for 11084832201 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer dryer combo repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11084832201
556-570 of 609
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

the lint filter needed to be replaced

  • Customer: Kathleen M from McDonough, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I took the old filter out and placed the new one in the same spot.

dryer runs, no heat.

  • Customer: william from williamstown, NJ
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
looked at schematic diagram, compared to unit finally used a multimeter to check fuse.. replaced fuse, assembled dryer and turned on to check operation. OK.

Dryer Makes Loud Noise

  • Customer: Danny from New Albany, IN
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Had to unstack the unit took it apart and replace the rollers,Belt and Idler Pulley It was the pulley making the noise but I had it a part and for the cost I replace the rollers and the Belt the Job was easy The Washer and Dryer are Great we run about 2 Loads a Day

Dryer would not start one day

  • Customer: Larry from Bristol, TN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
went on-line to research the problem. found the site and listed the issue. agreed with the probability and ordered the part. it came in a few days. After I ordered the part I watched the short instructional video that was available from the site. the repair took about 10 minutes to pull out the dryer, remove the back, take off the old part and put on the new part - put the back on plugged it in and push it back then turned it on. DONE

Dryer would not start

  • Customer: Garland from Mustang, OK
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Checked motor and other components and found Thermal Fuse did not check out allowing voltage to motor. Replaced Thermal Fuse and Dryer worked

dryer was not hot

  • Customer: arman from mclean, VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
the only thing i do around the house is changing the light bulb, so when our dryer was not working and was about 5 years old, i was told it cost too much to repair and i am better of to get a new one so watched few clips on you tube and ordered the parts from partselect which came with instruction, i could not believe it spend about $100.00 and my dryer is working better than before. bottom line if i can do this anyone can.

Door keeps opening while clothes are drying

  • Customer: Patrick from Sanford, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video and after that made the repair, it was very easy and the video was a really big help. From start to finish it took me no longer than 10 minutes.

Loud screeching noise coming from dryer

  • Customer: Bert from Las Vegas, NV
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
After removing the back & top of the dryer,I determined the noise was coming the idler pulley.I went online w/ model # & found Partselect.com.I ordered the dryer repair kit (at my door in 3 days) which included all the rollers,idler pulley, belt & hardware.It was an easy job to do even tho instructions were for top control panel model (mine is a whirlpool duet- front control) I did try using silicone lubricant on idler pulley, which worked to quiet dryer for a couple days so my wife could use it while I was waing for parts.Two thumbs up to Partselect.com,I will be purchasing all my appliance repair parts from them..I own all whirlpool stainless steel appliances that have been very reliable,but it's nice to know I have Partselect to fix problems as needed.

Dryer was overheating

  • Customer: James from Deming, NM
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I removed the back of the dryer and then unscrewed the thermostat and fuse from the heating element shield and replaced with new ones. I simply reattached the back and did a test drying run. Good news, no overheating. Easy-Peasy

right part easy

  • Customer: JOHN from LAUREL, MD
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
self...right part thank you

Felt came loose on lint screen.

  • Customer: mary from enola, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
ILove your service. The part came in 3 days. Best parts service I have ever found. I was told by the dealer it would take 2 weeks to come in.

handle broke off of dryer door.

  • Customer: Daniel from Birmingham, AL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Followed the repair instructions on your website and was done in less than 10 minutes.

no heat, timer would not advance

  • Customer: christopher from rockhill, SC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Got parts in 2 days, fast and easy repair.

Dryer would Start

  • Customer: Mary from Lewisburg, TN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Took the back off pulled the thermal fuse off placed the new one in and put the back of hte dryer back on

Dryer wad making squeaking noise

  • Customer: Thomas from Spring Grove, IL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Wrench set
  • 0 of 0 people found this instruction helpful
Thank you for your part service. It saved me about $ 200.00 dollars by Sears not coming out to repair a simple problem.
All Instructions for the 11084832201
556-570 of 609