Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 11084832201 > Instructions

11084832201 Kenmore Washer Dryer Combo - Instructions

All installation instructions for 11084832201 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer dryer combo repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11084832201
526-540 of 609
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

broken door handle

  • Customer: danielle from palmer, AK
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
removed 6 screws from the dryer door and reintalled the new handle

Clothes dryer would not turn on/would not run

  • Customer: Harold from Centreville, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Queried the Internet for my model number of dryer. Found Part Select web site. Went to the site and entered my model number again. Found a list of common problems and my particular dryer problem was listed. Only two possibilities - thermal fuse or timer. Studied the diagnostic criteria for thermal fuse and that seemed to fit my situation. Watched the video of how to replace the thermal fuse. After watching the video, I was convinced I could fix the dryer. Ordered the thermal fuse and it arrived in about 2 days. Followed the instructions previously viewed on the video and replaced the thermal fuse. Success!! Mission accomplished!! I felt great that I had done this by myself with help from Part Select. A service call from a repair establishment would have cost about $130.00. I fixed my dryer for about $9.00 plus shipping cost of about $7.00. And I didn't have to wait for two weeks for a repairman to show up and occupy my whole day. I forwarded the Part Select link to all of my friends and relatives and told them to use Part Select for their repair needs. Awesome web page and service! Use them!

Needed a lint filter

  • Customer: Catherine from Benicia, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
It was simply a replacement filter. No work just replace in slot. Thanks for great service and for sending in one day! We were shocked that the part arrived in one day! Will use your service again!

Drum turning, but no heat

  • Customer: Erik from Chelmsford, MA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
I first pulled the drum and turned on the dryer. The igniter never turned on. So I unplugged the dryer from the outlet and measured the resistance of the igniter, which was ok. I pulled the back panel and checked the thermal fuse, which was open. I also pulled the lint system plenum off of the unit, which was clogged with lint. This probably caused the thermal fuse to overheat. I cleaned out the lint collection system, replaced the thermal fuse and re-installed the drum. dryer is now working fine.

d ryer heat element

  • Customer: willard from celeste, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
removed bottom panel & removed old element.

Dryer wont start

  • Customer: Alan from San Antonio, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
As per video instruction that came with the email order conf

dryer quit before clothes were dry except on the extra low setting. I got an E1 error reading

  • Customer: Betsy from Round Mountain, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
flipped THE BREAKER (very important!). Removed the cover on the bottom of the dryer (2 screws), made easier because dryer is stacked on top of washer. Removed the heater box (3 screws). Thermistor located on top of the blower housing (right side). removed old thermistor (2 screws) and unplugged the wires. Plugged the wires into new thermistor, installed the thermistor, replaced the heater box, then tested the dryer. It seemed to work fine. Replaced the cover. It has worked fine ever since.

Dryer shutting down two to five min. into cycle E- 1

  • Customer: Jack from Gilbertsville, PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
Removed the front lower skirt with two 1/4"hex screws. Vaccumed all inner parts exposed. Removed three 1/4" screws holding the blower housing.Memoved the bias thermister again two 1/4" screws. Make sure all inner exaust pipes and rear chimney gas or electric are clean and lint free. Re assemble and test the unit. Install the skirt and make sure the dryer is level Jack, Pa.

Dryer door would come open when running

  • Customer: Maryanne from Deptford, NJ
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed instuctions on video accept our appliance was the Duet HT model so we had a glass window to deal with. Just a few more screws to keep track of but otherwise a very easy repair.

Clothes damp after cycle was complete

  • Customer: Gregory from Tinley Park, IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced the thermistor, thermostat, moisture sensor and the moisture sensor wire harness and the problem did not clear up. Tested both coils on the gas valve and the ohms readings for all 3 tests were within range. The burner would light and work until it shut off for the 1st time, it would attempt to relight but the gas valve would not open. Replaced the coils with Part # PS334310, 'M' Series New Style Coil Kit and the problem was corrected.

dryer door would pop open

  • Customer: joel from enola, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
ordered new latch. Arrived promptly. Installed in 5 minutes. Actually easied than the video. Thanks

Broken Door Catch

  • Customer: Barbara from Oakland, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The Door Catch Kit had clear instructions for installation and included multiple replacement catches to fit several different sizes/varieties of dryers. I used a screwdriver to pry out the broken door catch, popped in the replacement, and was done! As usual, PartSelect had what I needed at a good price, with clear instructions for any needed installation. Fast shipping, too.

Dryer was not heating

  • Customer: Tony from San Antonio, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
First I changed the thermal fuse. Still did not heat up. Then changed the heater element. That fixed the problem.

No heat

  • Customer: Ernest from Duncan, SC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
The thermal cutoff kit was bad. I followed the instructions in the video on the website to repair the dryer. According to some extra research that I did, the heating element is protected by the thermal cut off kit so there is a greater chance that the thermal kit will need to be replaced before the element will. There is a chance that the element could go bad, but more than likely it ise thermal cutoff kit.

Dryer does not heat

  • Customer: James from Forsyth, MO
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 0 of 0 people found this instruction helpful
First I reviewed the diagram to become familiar where items were located. I then insured unit was unpluged I used nutdriver to remove front cover from dryer. Noticed a lot of lint. Good time to vacuum it made finding screws and wires easier.Next Located heating element as described in parts location diagram. Utilized small socket to remove screws in cover plate. the socket set allow easy access to screws under cover plate. Removed 2 electrical wires from heating element. Pull heating element from housing with needle nose pliers. Had to tug a little, inspected element and found break in heating coil.Placed in new element by using reverse installation procedure. (didn't replace lint)This was an easy fix and I saved lots of dollars on repair or hundreds on new dryer. I spent about 20 minutes on the entire project. If you can read you can do this project. Very easy to complete. PS Ordering the parts was easy and arrived earlier than exepected.
All Instructions for the 11084832201
526-540 of 609