Models > 11082832100 > Instructions

11082832100 Kenmore Dishwasher - Instructions

All installation instructions for 11082832100 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11082832100
301-315 of 338
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer door wouldn't close.

  • Customer: John from Mountain Top PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Repair was very easy simply used a screwdriver to remove the cracked old latch and used my fingers to insert my new latch.

Dryer would not start

  • Customer: John from Commack NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
I did continuity tests on the on/off push switch and the thermostats - all were good. After some research I discovered the thermal switch which is somewhat hidden on top of the blower. Sure enough, it failed the continuity test. The two sheet metal screws are difficult to loosen from the access door at the bottom of the dryer. You can test the fuse from that location but it's more difficult to replace it without taking the entire dryer apart, which is what I ultimately did. Once the drum is out the fuse is very accessible. However, if you need to make this repair, try replacing the fuse from the lower panel (and avoid the time/effort in removing the drum). You might be able to use a 1/4" open-end wrench (or pliers) to loosen the sheet metal screws. I only had a standard ratchet set which is too big to fit into that tight space. Either way, it's not a complicated repair...watch the installation video - it's not exact but it's close enough to guide you through this.

No Heat

  • Customer: deborah from millstadt IL
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
The dryer was spinning, but the display said "sensing" for the whole cycle, and there was no heat. We took off the front of the dryer and the fuse was below the drum. This was an easy swap out, but it didn't fix the dryer. Then we ordered a thermistor, which also was an easy swap out but didn't fix the dryer. Last, we bought an ohm meter and tested the heating element, and discovered it did not have continuity. I had already ordered the heating element, as that was the next item to check on the list. The element was much harder to replace, because you have to take off the drum.

One was missing

  • Customer: Keith W. from Rushville OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Popped the panel open & replaced the one that was missing with a new one!

Dryer not heating

  • Customer: Matthew from Italy TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
1) Unplug dryer from wall. 2) Remove bottom panel on front of dryer below door. There are 2 screws. You will need a 1/4" nut driver. 3) Remove 2 screws (same size) holding the clip in place at the front of the element housing. Then remove clip. 4) Pull housing and element forward. Will take some twisting and angling to get it out. 5) Make a diagram showing which wires go to what terminals. Then pull wires from terminals. (Now would be a good time to remove lint and trash or in my case that bank card I lost last year from bottom of dryer.) 6) Remove screw holding coil inside housing and pull coil from housing. Use pliers and some muscle. 7) Install new coil and replace wires, housing, and panel doing this process in reverse. For internal bias thermistor, while front panel is off, find the part inside. It is toward the center near the front of the dryer. There are 2 wires and 2 screws 1/4" hex heads. Remove wires, remove screws, and replace.

Broken door handle

  • Customer: Charles from Escondidio CA
  • Difficulty: Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Although there were several diagrams available online discussing how to reverse the door direction nothing was available telling you that the door needed to be completely taken apart to replace the door handle. The screws holding the door handle are inside the door. Easy once you know that. I took the door off (following the door reversal directions) then took the screws holding the door together apart. It took a bit to take the broken pieces inside the door out because they have been exposed to such high heat for so long. Take your time and have patience so you don't break something else:)

Grinding and squeaky noise coming from dryer

  • Customer: Dennis from Claremont CA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
Found a YouTube video with step by step instructions for disassembling a Whirlpool Duet dryer. Though not the same model as mine it was close enough. The hardest part of this repair was figuring out how to pry apart the elctrical connectors but it's pretty simple once you get the hang of it. You also might want a little help taking off the door. It's not mandatory ( I'm a big guy and I managed it by myself) but having an extra pair of hands makes things easier. If you can take out screws and remember the order you took them out you should not have any problems. The actual pully assembly was held in my one bolt, easily replaced once you get access to it. If you don't want to change out the belt, removing the door is not necessary as you can get to the pully from the back side of the machine. But since you have it halfway disassembled already, you might as well go for it and not have to make a return visit. Total time including vacumning out all the lint from inside the dryer was three hours. Took my time and saved myself a few hundred dollars for sure.

No Problems

  • Customer: Bruce from Kent WA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
No Problems

broken dryer handle

  • Customer: GILL from burbank CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unscrew the philip screws only, note as you unscrew each one get some painters tape and tape the screw above each hole so as to remember which screws go back. They are not all the same, panel falls right off take of handle screws and replace.

Idler pulley bearing was sqealing

  • Customer: David from El Paso TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Disconnected the power and duct from the dryer. Removed the back and top of the dryer by removing the 1/4" screws. Created slack in the belt by compressing the spring and moving the idler arm.Slid the belt off the pulley. Removed the tri-ring clip, slid the old pulley and gasket off. Cleaned and inspected the shaft and vacuumed the inside of the dryer. replaced the gasket, pulley and tri-ring clip. Replaced the top and back of the dryer. Connected duct and power.

not drying clothes

  • Customer: gene from leesburg GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
The repair was easy and very simple. With nut driver removed front cover. Noted the wiring set up and removed. Lifted heat tunnel up and pulled it from the case. Removed the old heating element and install new one. Reinstalled the heat tunnel reconnected the wires. Slide tunnel back into position. Replaced screw and you are done. I always pray and ask Jesus for his help and things always go well.

Dryer won't get hot

  • Customer: Dan from Port st lucie FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Unplugged unit. Took off the lower kick plate took the old element out and put the new one in. Works great.

Dryer element burned out. Dryer would not heat.

  • Customer: Cassandra from Idaho Springs CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
I was afraid I had to go in from the back panel, undo a million little bolts, after pulling the whole thing out far enough to get behind the dryer. Not so! I watched the installation video. I cannot get to the 220 plug easily so I turned of the switch at the breaker box. I opened the small panel on the front of the dryer under the dryer door. Loosened one bolt on a cover guard to expose the element. Unplugged the connection to the element and easily pulled out old part. Slipped in the new part, reconnected the little plug connections, closed cover panel.! Voila! Done! My Husband was amazed that I was done & we were ready to go again & my grand kids cheered for me!! 15 minutes or less instead of hours.

No Heat From Dryer

  • Customer: Henry from Round Lake IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Searched Internet for Dryer Model and problem, purchased the three items listed used in the heater element - long as I was replacing parts I was going to do them all...Unplug Dryer, Removed Back and Front Access panels using power driver with nut socket adapter... Lots of Dust Build Up in lower section of dryer, cleaned by hand, then vacuumed and the blew out with air from small compressor. Removed heater assembly and replaced All Three Electrical components, (Heater coil, High Limit, Thermal Fuse) Reinstalled heater unit and then closed up unit back panel and front panel. Plugged in, ran dryer front panel diagnostics - no errors reported, test dryer - dryer vent tube is now warm to the touch - the dryer working again.... (Suspected Bad Item: Thermal Fuse) Total repair time once parts in hand was about two hours, most time was spent cleaning out lint and dust to insure no fire hazard present

Clothes were not drying on auto sensor.

  • Customer: Michael from Annapolis MD
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed standard instructions regarding removal of top first & then the front panels. Realized after following this process that I did not have to remove top, but only one of front panels to obtain access to moisture sensor. If I have to do this again, the replacement of sensor will be much easier.
All Instructions for the 11082832100
301-315 of 338