Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 11082822102 > Instructions

11082822102 Kenmore Dryer - Instructions

All installation instructions for 11082822102 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11082822102
556-570 of 609
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer wad making squeaking noise

  • Customer: Thomas from Spring Grove, IL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Wrench set
  • 0 of 0 people found this instruction helpful
Thank you for your part service. It saved me about $ 200.00 dollars by Sears not coming out to repair a simple problem.

broken drive belt

  • Customer: Andrew C from West Springfield, MA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
after watching the instuctional installation video, it real took about 25 to 30 mins to install the new belt. The video was perfact and made the installation so easy..

Dryer overheated and thermal fuse blew.

  • Customer: Calvin from Klamath Falls, OR
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
removed back cover and with unit unplugged, removed one wire from each device (thermal fuses and switches) and measured with multimeter. Found thermal fuse open. Removed and looked up and ordered part. Installed fuse and buttoned er up and all good. Hardest part was putting the exhaust hose back on the floor outlet!

Dryer kept shutting off after 10-15minutes

  • Customer: Neal from Bertha, MN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Took off front bottom panel reached in removed part that was very dusty. Put in new part. Cleaned out lint inside dryer. Works like a charm.

Dryder would not work.

  • Customer: John from Alton, NH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Removed back and found fuse bad, repalced fule.

Dryer quit heating

  • Customer: Jeff from MANCHESTER, GA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Was able to change out the Heating element but the dryer still does work....

Dryer tumbler runs, but no heat

  • Customer: Tim from Palmdale, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
At first I thought it was the ignitor, so I replaced it. No luck there. Next I went to the Part Select web site...that showed that the Thermal Fuse was the cause of this symptom 45% of the time. I installed the fuse and now my dryer is working!

lint filter housing cracked

  • Customer: Richard from Sanford, ME
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
open dyer door replace lint filter perfect fit, good price, fast delvery. thank you

no heat

  • Customer: jacqueline from lackawanna, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
downloaded video

Worn/Broken Thermal Fuse

  • Customer: Donald from Lake Elsinore, CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Removed the old fuse and replaced with the new fuse. Of course, I had to remove the back of the dryer but very easy and the cost was less than $20.00. Definitely worth it because we did not have the money for a new dryer. PartSelect.com is awesome!

dryer would not get hot on any setting

  • Customer: Betsy from Round Mountain, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
First I replaced the heating element. That did not fix the problem, so I used an ohm meter to test the thermostat and fuse (thermal cut-off). One of those was bad, so I ordered the thermostat/fuse conbo and put those in. The hardest part was getting the wires to the right places. I labeled them with masking tape and a sharpie, but maybe they are sized so they only fit one place. I didn't check. The actual work of changing out the parts was super easy. I recommend testing those three parts-heating element, thermostat, fuse-with an ohm meter before buying something you don't need. I now have a spare heating element and thermostat. I should be good for another ten years!

Dryer was tumbling but no heat

  • Customer: Karen from Hatboro, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
When the part came in my husband was not home and I figured I could put this part on myself. I took the part downstairs, used the nut driver to remove one screw, took the two wires off the old therma fuse, put the wires on the new therma fuse, and screwed the new therma fuse onto the back of the dryer. It really couldn't have been any easier.

was not drying

  • Customer: Barbara from Woodland Park, CO
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
took of the back , took out the drying coil ,put the other in , but back on . now it works saved alot of money. love it. Thank you parts select.

Dryer not heating up

  • Customer: anne from grand rapids, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
This has happened several times to my KitchenAid dryer. It cost more than $100 to bring someone in to repair. Fortunately, I saved my bills and saw the part "thermal fuse" listed. I researched that and found your website. I couldn't believe how easy it was to fix. The part cost less than $15 and the diagrams you provided were a big help. I was about to purchase a new dryer, easily $500. Your site saved me a bunch of money. How I fixed? Unscrewed the back panel of the dryer. Found a part that resembled the part you sent me. Slipped it out. Put the new one in...that is it. I also figured that one reason the part keeps burning out is because my duct has to bend to get to the outside vent. The obstruction probably causes the dryer to overheat more often than not. I pulled the dryer 6 inches more away from the wall to see if that helps. My fuse was going out about every 2 years.

Dryer would not turn on.

  • Customer: Cassondra from Weaverville, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Was working fine one load and not the next. I remembered we had used this site for our dishwasher so gave it a try. Went with most common problem first. Ordered Sun rec'd Tues. Took longer to vacuum the back of dryer then it did to replace the fuse. Cost less than 30 bucks including shipping. Video was cool too.
All Instructions for the 11082822102
556-570 of 609