Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 11082822102 > Instructions

11082822102 Kenmore Dryer - Instructions

All installation instructions for 11082822102 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11082822102
31-45 of 609
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The Dryer Would Not Turn On

  • Customer: Ribhe from Wildwood, MO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 16 of 16 people found this instruction helpful
The dryer wouldn’t turn on at all. It was like it was unplugged from the wall. However, fixing it couldn't be easier. I simply removed the back panel, found the fuse, tested it with an Ohmmeter (to determine that this was the part that didn't work), ordered the part from this website, and replaced the part. The part arrived in about two days. The shipping was a little pricey, but overall the whole thing cost me $20 vs. whatever it would cost me to get someone else to repair it. The website helps to identify the problem, and it is helpful to read how other people fixed their problems. It was so easy and the service was so good, I will definitely use this website again and recommend it to others.

Dryer door catch broke

  • Customer: Bill from Houston, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 16 of 17 people found this instruction helpful
The old catch on my dryer door was gone and I was keeping the door closed using tape. I ordered the part and it arrived with no hassles in about 5 days. The repair was too easy. I just popped the new catch in place. It took all of about 30 seconds to complete using no tools. I wish all home repairs were this easy.

Poorly designed lint filter/ gasket falls off

  • Customer: John from Madison, WI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 19 of 27 people found this instruction helpful
Replaced

Dryer turns off after 1-2 minutes

  • Customer: Dixon from Santa Fe, NM
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 14 of 15 people found this instruction helpful
I tried to follow directions followed by others on this site after diagnosing the problem via suggestions provided by users. I have a Whirlpool Duet dryer from 2002. We've had problems since moving about 3 years ago. I removed the front panel (lower) by unscrewing the two bottom screws (1/4" sheet metal screws). Then I took out the lint screen and the metal tube/contraption immediately beneath to get access to the area where thermistor is located. See the drawing/chart to help you locate this. It's really easier than it seems. Make sure you have the chart/drawing for your model - it makes difference! The thermistor came out pretty easily with a nutdriver that has a swivel offset shaft. Ask your hardware store tool dept. about that one. Put everything back in reverse order of course and test either with/without the front panel re-attached. In my case it fixed at least part of the problem. I was able to get clothes almost dry with most settings but I have yet to install the moisture sensor to see if that helps in addition to the internal-bias thermistor. I am the kind of person that does one thing at a time so at least I now know the thermistor was bad. Good luck and hang in there with your own repair. It's a lot cheaper even if it takes you longer to do than a pro.

Dryer not spinning

  • Customer: john from goldsboro, NC
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 20 of 35 people found this instruction helpful
I took off the front panel via 2 screws on the inside of the dryer with the top panel in the maintenance position. Pulled out the tub(cut my hand pretty bad in the process but continued). Did some cleaning and I had to google how the belt tensioner goes into place. Rather difficult on your own i held the belt and placed the tub back into place while placing the belt around the tub putting it in the correct area. thats pretty much it and began reinstalling the parts i had removed.. easy fix now that i have done it once. This is all after my landlords said they werent replacing it and just to have this one hauled off, so all in all i have a 26 dollar dryer now:)

The felt strip on the filter had come undone.

  • Customer: Rebecca from Laredo, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 16 of 24 people found this instruction helpful
Took the old filter out and inserted the new one- works great!!

Dryer would not start - bad door switch

  • Customer: Paul from Robbinsville, NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 20 of 36 people found this instruction helpful
Removed to top panel - two screws in the back
Removed the screws from the metal panel holding the electronic board, remove the wire clips and rotated the metal panel up and out of the way.
Disconnected the three wire connector to the door switch cable - There must be a special tool for this as a basically destroyed the connector on the door switch cable.
Use a pliers to pull out the door switch from the front. This was not easy and I wound up having to destroy the door switch to get it out.
Inserted the new door switch cable first from the fron of the dryer and connected the new door switch cable connector to the dryer wiring harness.
Rotated the main electronic panel back in place, re-inserted the cable harness and re-inserted the bracket screws.
Re-installed the top panel and screws.

Dryer runs with no heat

  • Customer: Paul from Bradford, MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 13 of 16 people found this instruction helpful
It was easier to remove the blower manifold cover, (3 screws) to get at the heater element. Remove the heat shield, disconnect the two wires from the element. There is another screw on the side holding the element in the housing. Remove it and slide the element torward you. I used pliers as it was a snug fit. Replace. Good time to vacuum the whole area.

doo handle broken

  • Customer: Keith from Anthem, AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 12 of 13 people found this instruction helpful
I followed the directions of a previous customer, using a Phillips screwdriver to remove only the Phillips screws on the inside of the door. Removed the outer plastic ring around the door. Replaced the handle (attached by two screws) and put the plastic ring with a new handle back on the outside of the door.

dryer wouldnt heat

  • Customer: JEFF from LEBANON, TN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 17 of 28 people found this instruction helpful
First i tested each part for continuity and found out that the thermal fuse was bad. So ordered the part and went ahead and got thermostat and element to ensure no problems in the future since I already was in there.

noisy drum

  • Customer: Jeff from Mesa, AZ
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
  • 13 of 16 people found this instruction helpful
the job would have gone faster if the right parts had been sent in the first place. I would have never paid for two day shipping. In the repair, I removed the rear panel, clipped the plastic triangle holding the bearing, installed the new bearing and new clip.

seal for lint filter came off

  • Customer: John from Midland, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 13 of 17 people found this instruction helpful
Pulled out the old and slid in the new filter

craked blower motor

  • Customer: joe from cheswick, PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
  • 43 of 107 people found this instruction helpful
somthing fell down in the blower motor compartment and busted up the bloewr motor fan,and was making noise and out of balance.i changed the blower motor and runs like a charme

Flashing E1 code for a bad thermistor

  • Customer: John from Cedar Rapids, IA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 14 of 22 people found this instruction helpful
I replaced the thermistor earlier, but the code was still flashing. I noticed the heater terminals were charred and pretty well covered in carbon. So, I replaced the heater, the thermostat and thermal fuse and replaced the 3/8" spade terminals on the heater wires. (These are hard to find - most electrical spades terminals are .250. Also, I crimped and soldered these for a connection with the lowest resistance possible). After all that, the code still flashed! I let the explatives fly, calmed down, and ran the control board test. (This is done by pressing "more time" "less time" "more time" "less time" in succession.) The control board was passing all the tests, but the thermistor test, and the only thing is in this circuit is the thermistor, the wires, the connector to the control board, and some circuit on the control board that involves a few resistors and the "brain" chip. So, I checked the terminals at the thermistor, the wires up to the control board and the connector at the board. The control board connector was fairly dust encrusted, so I unplugged it, cleaned the control board terminals and sucked away all the lint and dust. Finally, I carefully removed earch crimp terminal from the Molex connector (the white female connector) and cleaned and bent them to yield a better connection to the terminals on the control board. I put it all back together, and thus far it is working fine.

Idler Pulley broke

  • Customer: Keith from Richmond, VA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 11 of 13 people found this instruction helpful
I disconnect the power, then the vent pipe. I removed the back panel of the dryer to access the pulley and removed the belt. Replaced the back and put everything back together.
All Instructions for the 11082822102
31-45 of 609