Models > 11082822102 > Instructions

11082822102 Kenmore Dishwasher - Instructions

All installation instructions for 11082822102 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11082822102
406-420 of 601
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Idler pulley bearing was sqealing

  • Customer: David from El Paso TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Disconnected the power and duct from the dryer. Removed the back and top of the dryer by removing the 1/4" screws. Created slack in the belt by compressing the spring and moving the idler arm.Slid the belt off the pulley. Removed the tri-ring clip, slid the old pulley and gasket off. Cleaned and inspected the shaft and vacuumed the inside of the dryer. replaced the gasket, pulley and tri-ring clip. Replaced the top and back of the dryer. Connected duct and power.

not drying clothes

  • Customer: gene from leesburg GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
The repair was easy and very simple. With nut driver removed front cover. Noted the wiring set up and removed. Lifted heat tunnel up and pulled it from the case. Removed the old heating element and install new one. Reinstalled the heat tunnel reconnected the wires. Slide tunnel back into position. Replaced screw and you are done. I always pray and ask Jesus for his help and things always go well.

Dryer won't get hot

  • Customer: Dan from Port st lucie FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Unplugged unit. Took off the lower kick plate took the old element out and put the new one in. Works great.

Dryer element burned out. Dryer would not heat.

  • Customer: Cassandra from Idaho Springs CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
I was afraid I had to go in from the back panel, undo a million little bolts, after pulling the whole thing out far enough to get behind the dryer. Not so! I watched the installation video. I cannot get to the 220 plug easily so I turned of the switch at the breaker box. I opened the small panel on the front of the dryer under the dryer door. Loosened one bolt on a cover guard to expose the element. Unplugged the connection to the element and easily pulled out old part. Slipped in the new part, reconnected the little plug connections, closed cover panel.! Voila! Done! My Husband was amazed that I was done & we were ready to go again & my grand kids cheered for me!! 15 minutes or less instead of hours.

Dryer would not start.

  • Customer: Carl from OFallon IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
I tried all standard tricks: checking circuitry, switches, etc. Then I read other submissions on your site, which suggested this thermal fuse was the culprit on almost 50% of cases. I got yours in 2 days, installed in no time, easy as pie. One caution: it will take an entire day if you forget to close the dryer door completely.

No Heat From Dryer

  • Customer: Henry from Round Lake IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Searched Internet for Dryer Model and problem, purchased the three items listed used in the heater element - long as I was replacing parts I was going to do them all...Unplug Dryer, Removed Back and Front Access panels using power driver with nut socket adapter... Lots of Dust Build Up in lower section of dryer, cleaned by hand, then vacuumed and the blew out with air from small compressor. Removed heater assembly and replaced All Three Electrical components, (Heater coil, High Limit, Thermal Fuse) Reinstalled heater unit and then closed up unit back panel and front panel. Plugged in, ran dryer front panel diagnostics - no errors reported, test dryer - dryer vent tube is now warm to the touch - the dryer working again.... (Suspected Bad Item: Thermal Fuse) Total repair time once parts in hand was about two hours, most time was spent cleaning out lint and dust to insure no fire hazard present

Dryer was Dead...did absolutely nothing

  • Customer: Terry from Bloomingburg NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
went thru all the electrical connections, finally checked the thermal fuse..it was the culprit. next time I start there. unlike older dryers, where one component gos such as the drum belt or the heating element and its only 2 years old. This thermal fuse shuts down the entire unit when it malfunctions

dryer would run but no heat

  • Customer: Ryan from cleveland OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I took rear panel off with a nutdriver 8 screws.disconnected the 2 wires that went to thermal fuse and removed 1 screw holding it in place.replaced thermal fuse and reconnected wires and rear panel.turned dryer on. had heat. walk in the park!

Clothes were not drying on auto sensor.

  • Customer: Michael from Annapolis MD
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed standard instructions regarding removal of top first & then the front panels. Realized after following this process that I did not have to remove top, but only one of front panels to obtain access to moisture sensor. If I have to do this again, the replacement of sensor will be much easier.

Door latch mechanism broke and fell into door

  • Customer: Peter from POTTSTOWN PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Step 1: remove new latch from bag in which part comes. Step 2: push latch into hole where the other latch was. Step 3: enjoy having a dryer you dont have to hold closed with a folding chair.

Dryer had a high pitch squeal, first at startup, then during full cycle.

  • Customer: Dustin from Rochester MN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the top panel of the dryer via a couple of screws from the rear. Remove the rear panel swing it open light a door to the right, minding the electrical connections. Removed the belt from the pulley, removed the Tri-ring from the shaft and slid the pulley off of the shaft. The shaft was slightly rusted so I used a steel brush and brake cleaner to clean it up, placed the new gasket, pulley, and tri-ring on, replaced the belt, and put the panels back into place. As the dryer is about 7 years old, also removed the front lower panel and cleaned out unit which had quite a bit of accumulated dust and glitter especially in the vent lines. (3 girls live here). Pretty easy, most screws remove with just the one tool.

Dryer would not heat up, but ran.

  • Customer: Bart from Hillsdale NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Could not be any easier. For less than $20 and 15 minutes time, I couldnt be happier.
All that was needed is a nutdriver to remove a 1/2 dozen screws to take the back panel off. Then a phillips screw driver to remove the thermal fuse. Unplug 2 wires and then attach them to the new fuse. Put it all back together and done!. Working dryer.
PS: I had enough gas line and ducting connected to the dryer ,so thatt I was able to get behind it with out removing them. This may have taken another 15 min. if I needed to do this and two adjustable wrenches.

dryer not heating

  • Customer: eugene from cheshire CT
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I checked the thermal fuse for continuity and had none.ordered part arrived next day. I took a picture with phone to idenify wires. installed in a short time.dryer works like new

felt gasket had come loose!!!!

  • Customer: Charles from Phoenix AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
remove&replace

The dryer just stopped working one day

  • Customer: Tobias from Glenside PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
To make sure the dryer didn't die catastrophically, I checked to make sure the timer, the light, and the push to start start switch and the door switch were still working. After they were diagnosed to be working properly, I unplugged the dryer and pulled it back from the wall so I would have enough room to work behind it. The first item you will need is the wiring diagram. If you do not have one, one can be obtained online by using your dryer brand and model number. The next thing you will need is a quality digital multimeter that measures resistance or continuity. The last thing you will need is a 1/4" nutdriver. The first thing you will need to do is remove the exhaust tube from the back of the dryer. The second step is to remove a small black plate located near a green ground screw. The 3rd step is to remove the large black cover on the back of the dryer. Once this is removed, you will need to locate the thermal fuse. The thermal fuse is a small component that has 2 blue wires connected to it. It is located on the housing where the steam from your clothes leads to the exhaust port. The first thing you need to do is disconnect the 2 blue wires. Once the wires are disconnected, set the multimeter to resistance. The unit of resistance is ohms and the greek letter omega is used. The red lead of your multimeter goes one metal tabe of the fuse and the black lead goes on the other one. If the multimeter measures 0. L ohms, then the fuse is bad and needs to be replaced. If the multimeter reads 00.00 ohms then the fuse is good and you have another problem. I hope these instructions were useful.
All Instructions for the 11082822102
406-420 of 601