Models > 11082822101 > Instructions

11082822101 Kenmore Dishwasher - Instructions

All installation instructions for 11082822101 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11082822101
211-225 of 324
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer quit heating

  • Customer: Jeff from MANCHESTER GA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Was able to change out the Heating element but the dryer still does work....

lint filter housing cracked

  • Customer: Richard from Sanford ME
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
open dyer door replace lint filter perfect fit, good price, fast delvery. thank you

dryer would not get hot on any setting

  • Customer: Betsy from Round Mountain TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
First I replaced the heating element. That did not fix the problem, so I used an ohm meter to test the thermostat and fuse (thermal cut-off). One of those was bad, so I ordered the thermostat/fuse conbo and put those in. The hardest part was getting the wires to the right places. I labeled them with masking tape and a sharpie, but maybe they are sized so they only fit one place. I didn't check. The actual work of changing out the parts was super easy. I recommend testing those three parts-heating element, thermostat, fuse-with an ohm meter before buying something you don't need. I now have a spare heating element and thermostat. I should be good for another ten years!

The dryer was taking longer to dry.

  • Customer: Brett from Billings MT
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
My dryer is one of the energy efficient models (HE). The video for the installations was knowledgeable, but getting into the front of mine only required removing to screws from the bottom left & right corner (not using a putty knife to pop the springs). the plate on the front drops after that. Also when taking out the tube with the dryer element in it took a lot more twisting inside the frame to get it loose. Still turn it after the wire connections have been pulled off a little bit better than 1/4 of a turn. Also the heating element was in there really, really tight. It required tapping on the plate with a screw driver and a rubber hammer to take it out & put in (not that tough). After putting it in a 1/4 of a turn so that the tab was inside the blower tube. everything after that was pretty easy. The video showed this all being done in a clean dryer. It has been my experience that before all is running & closed back up that a vacuum or shop vac needs to go thru there to clean things up & prevent a future fire.

Belt pulley frequently squealed loudly

  • Customer: WILLIAM from HOUSTON TX
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
My way of replacing the pulley was much faster than the parts select video that showed how to replace the belt tension-er pulley. They took off the door, the entire front AND the drum to get to the pulley. I ACCESSED THE PULLEY BY REMOVING THE 4 INCH EXHAUST PIPE, (ONE SCREW) WHICH GAVE MORE THAN ENOUGH OPENING TO REPLACE THE NEARBY PULLEY! I suggest you remake that video

No heat

  • Customer: Richard from Mount. Pocono PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Easy fix. Took the front panel off, removed the heater tunnel by loosinig the two holding screws. Pulled the whole duct out of the machine and swapped out the old parts for the new. Just reverse the removal procedure and done. One thing to do is to check the exhaust duct to make shure it's not clogged. That was the reason my heating element broke.

The leveling foot on my dryer broke.

  • Customer: Diana from Clifton NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
We only had to tilt the dryer enough to be able to screw the leveling leg in place.The only hard part was holding the dryer steady to screw in the leveling foot.

Suspected bad moisture sensors

  • Customer: David from Sussex WI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Opened machine up, removed electric control panel, removed door assembly, removed lint collector assembly, removed and replaced 2 sensor bars then reassembled machine. Ended up not being the problem but, I now have new moisture sensing bars.

Lint filter tore causing hang up with metal guide

  • Customer: Mark from Layton UT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed lint filter cover (3 screws). Removed old lint filter. Adjusted metal guide. Reinstalled lint filter cover (3 screws). Installed lint filter. Replacement filter is a like quality.

replace handle

  • Customer: heinrich from el paso TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the instructions, by removing 6 screws from the inside on the door. Than I replaced the handle with the 2 screws that hold the handle. After placing everything back in place I put the 6 screws back and had a new looking dryer! The replacing is easy, I just think the price for the handle is to high!

no heat

  • Customer: Marshall from Cortlandt Manor NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed existing parts and replaced with new high limit thermostat and thermal fuse kit,replaced flue and tested. Worked like a charm.

lint filter gasket broken

  • Customer: Bob from Howell NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
replsce

door would not close catch fell within the door

  • Customer: Richard from Marmora NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Pushed the new catch in by hand. Working great.

Squeaky tension pulley

  • Customer: Trevor from Puyallup WA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Very easy repair... The video was really helpful too. I was able to find a different video that was closer to our model. (Front Loader HE) It probably took me a little longer than needed but I took the time to shop-vac everywhere I could, since it was all easy to get to. I opted for next day shipping so the shipping charges were more than the part. Tools I used were: Cordless drill-screw driver, 1/4in. socket, Phillips head bit and needle nose pliers for the control panel connections. Thank you again for making this so easy. Saved us a lot money by not calling an appliance repair tech.

Replace. Motor

  • Customer: Jon from Markham VA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
Getting the fan off proved to be quite an issue. on my model, it loosened in the clockwise direction. I ended up having to completely pull the motor and clamp the unit in a vice before I was finally able to gett itloose.. Hopefully yours will not be such a problem....
All Instructions for the 11082822101
211-225 of 324