Models > 11076942500

11076942500 Kenmore Dryer - Overview

Get Parts and Repair Help for 11076942500

If you know the dryer repair part you need, you can browse the list of all parts on the 11076942500, or you can search by name or part description. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for 11076942500 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$15.20

Thermal Fuse

This part is a one-time use thermal fuse which attaches to the blower wheel housing of your clothes dryer. It cannot be re-set and must be replaced when continuity between the pins...

$14.60

Cycling Thermostat

Cycling thermostats continually cycle the heating element off and on to maintain a constant inner temperature. This particular cycling thermostat has a limit of 155 degrees Fahrenheit and a differential of 25 degrees. Meaning that with this thermostat, the heating element will cut out at 155 degrees and cycle back on once the internal temperature drops by 25 degrees.

$28.26

Lint Filter

This filter collects lint as it passes through the dryer vent.

$16.53

'M' Series New Style Coil Kit

This gas dryer ignition coil set comes with two ignition coils: one three terminal Boost/Hold coil, and one two terminal secondary coil.

$4.76

Door Catch Kit

This dryer door latch kit comes with one plastic door latch and one metal door strike.

$18.41

Door Switch - 3 Wire

A door switch is a simple on/off mechanism that prohibits the dryer from operating when the door is open.

$13.86

Idler Pulley with Tri-Ring and Gasket

A dryer's idler pulley helps the belt to rotate the drum. Also known as dryer belt tension pulley wheel.

$4.46

Thrust Washer

$37.37

Igniter Kit

This silicone carbide igniter with ceramic holder kit includes the 3" flat igniter, bracket, 5" wire leads, and the plug. Able to replace both round and flat igniters, this kit is ...

$17.28

Multi Rib Belt

This dryer drum belt from Whirlpool/Kenmore has five ridges. It is used for many of Whirlpool's brands of clothes dryers. This flat belt is 1/4 of an inch wide.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer was working, but no heat.

  • Customer: ANTHONY from CHESHIRE CT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 809 of 940 people found this instruction helpful
First I unplugged the dryer, then removed the back panel, this exposed most all of the wiring and I could see the heater coils.
Not knowing what the problem was I started looking at the coils and could not see any broken parts.
So then checked the thermal fuse for continuity I removed the two wires from it with a small pair of needle nose pliers, ... read more

dryer would not turn off with door open

  • Customer: RICHARD from NORCROSS GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 385 of 387 people found this instruction helpful
pryed dryer top open and opened front door.. unscrewed the 2 retaining screws. pulled old switch from the wiring harness.
put new switch in place and replaced the retaining screws.
put new switch wire plug into the wiring harness. before closing top, checked door switch function with dryer on.
dryer cut off when door open and when close... read more

Dryer wouldn't turn on b/c door switch broken

  • Customer: April from Xenia OH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 280 of 350 people found this instruction helpful
It was simple once I figured out what to do:). I removed the 2 screws on the top of the dryer... they were a bit hard to find. Even with the other descriptions on this site. I was removing things I didn't need to. The 2 screws you need to remove are under the LINT COLLECTOR LID. Remove those 2 screws & lift the lid... it will be tight at first. the fro... read more