11068712890 Kenmore Dryer - Instructions

my friends came over and helped me. we loved the instruction video. made it much easier.

I won't tell you how we did it, but I'll tell you the right way. Unplug. Remove the exhaust tubing attached to back of dryer. Pry the top up from the front and lean it against the wall. Un plug the wires attached to the front panel (remember where they go) Remove screws at top sides of front panel. "lift up" and remove. Close top. Lay machine on its back. We used a couple of 2x4's to lay it on so as not to crush the vest collar. Clean it out, including lint filter. The new belt wraps around the drum, you will see the channel about midway on drum. Feel behind the motor on the lower right side. There is a shaft with a channel for the belt. Immediately next to that is another pulley type arm with another channel for the belt. This arm moves stiffly and puts tension on the belt when installed correctly. Look at the diagram included with the new belt which shows the path of the belt. Wrap the belt, ridges against the drum and then around the motor shaft. At this point you have to physically pull the last arm out to allow the belt to wrap around the channel provided. If the belt is not twisted , the job is done. Turn the drum with your hands to make sure it is turning properly. Replace the front panel, plug in the electricals, replace the screws making sure the drum is properly centered. Stand up the dryer. Plug in and turn on dryer to make sure everything is right. Replace the exhaust tubing and set into place. Sounds like a lot of steps but I have described the whole process for you beginners. The rest of you will know already. Good Luck . Oh by the way we are 69 and 71. If we can do it, so can you

Slid the dryer away from the wall and removed the screws from the top back panel. I then removed the screws that held the top section in place. Two more screws held the two full length metal together. After removing these the push to start switch is easy to remove. Disconnect the two electrical wires. With a screw driver lift the tab on the switch and twist the part 45 degrees and remove. Re-assemble in the reverse order.

Unplug the dryer, remove hot air duct. Remove metal dryer back to access thermostat using a nut driver. Unscrew one screw holding on thermostat, detach 4 wires, and replace with new unit, attaching 4 wires to new unit. Then reverse process to button up the dryer. Great how-to video on your site helped a lot!

I took off all the back plates of dryer. (2 sets). Then I took off the heating element. It appeared to be in tact but had some blackening coloration on plate. Ordered new part, replaced the element (tested before I put the back plates back on) and it worked perfectly again. I was especially happy with Parts Select because I ordered the part on a Sunday night and it arrived on Tuesday at noon (regular shipping)!!

after process of elimination ,figured had to be cut off switch followed simple instructions also watched your video..simple repair up and working again approx. 30 min. once i had kit. thanx 4 the help MIKE

I watched the video several times to make sure I got it right. The first thing that was very helpful was how to disassemble the top cover and front panel using a putty knife to disengage the detents. With the cover off I could acccess the belt and idler pulley. Replacing the belt was fairly easy as long as you note the way it threads through the idler pulley and drive pulley. I thought the video was excellent. It took me right to the problem and the fix. As a bonus the price for the belt was much lower from Parts Supply then from Sears. I've recommended this site to several others.

Just as your helpfull diagram of the dryer said, removed the rear panel,there it was, i recongnised it by the part you sent, pull it out of it's position, had a little truble figuring out the piece that fits on where the electric prongs are, after looking found out the piece was held on with a clip that goes inside the housing, Haaa. the rest was easy. Thanks,It works great. Dick

First I purchased the heating element, still no heat. Then I purchased the thermal fuse,still no heat. I have been pleased with the prompt shipment of the parts and the parts arrived safe. Thank you for service and time, not sure what to do now.I will recommend PartSelect to friends.

Unplug unit / removed back cover / went down , locating both parts to be replaced / simple one screw removal from each part / thermal fuse , one wire @ a time , reinstalled . / Cycling thermostat , 4 wires. Did one wire @ a time , reinstalled. / Putted back cover back on , plugged dryier back up, turned it on to run. To check for heat / yes, ran good as new. Later that day some more running , with damp clothes in it. Did it's job , dry.

I followed the repair method as described in the how to video it was as easy as that. Dryer is now working perfectly

Took the back off of the dryer, looked on "parts select" found what I thought might be the problem. Got the parts the next day. Put on new thermal fuse, then put on cycling thermostat. Wasn't sure which it needed, so put both on. Put the back of the dryer on hooked the gas up, hooked up to electric, & turned the dryer on. Back in business, everything works, dryer works as if nothing was wrong. Thanks to "parts select" saved me a repair bill.

I watched your video on how to replace the fuse.Wow it was a lot easier than I thought.I would highly reccomend anyone to watch the video before even trying to do any repairs.The dryer is working like a new one.By doing it myself saved me a lot of money.Thank you

Removed two screws at the top, removed two screws for the front panel, removed the broken belt, installed the new belt, followed the directions that were in the new belt package, and replaced all the panels and tested. It worked.

1.Unplugged power cord to Dryer. 2.Removed Dryer vent screen, unscrewed two screws located in dryer vent.3.Pried open top of dryer using putty knife. 4.Propped up top of dryer using 6 inch piece of wood resting on drum of dryer. 5.Removed screw holding door switch.6.Removed door switch from harness using putty Knife to pry apart connection. 7. Installed new door switch to harness and re-installed. 8.Removed wood used to prop open top, closed top, re-installed all screws, dryer vent and plugged dryer back up.