11068322700 Kenmore Dryer - Instructions

Trouble shot to failed motor. Ordered motor and new drive belt. The hardest part is figuring out how the dryer dis-assembles. Follow Parts Select on-line instructions. Also, several good instructional videos on You Tube! My recommendation is to order a new "blower wheel" when changing motor on a gas fired dryer. The heat combined with age bonds the blower fan to motor shaft. It had to be broken off in pieces to remove motor.

took off the broken belt and the idler pully went to the internet found your website watch the video and ordered the parts got the in 3 days took 15 mins to put them on and all is good

2 screws at lint tray 2 screws on back pick up top 2 screws in front under top lid separate front from drum slip in new belt screw front back to top route around tension pully put other 4 screws in complete so dry something

Popped top up Took front panel screws out. Looked for other damage. Put belt around the tumbler and got it hooked up. Grew an extra set of hands and re assembled front the checkd seals to make sure they where on and put top back down... Process is a pain in the butt i reccomend socket set channel lock pliers and a cold beverage or two

Pushed the new catch in by hand. Working great.

Removed top and front panels, lifted front of drum, slid new belt on drum then thru tension and motor pulleys. reassembled.

I watched the video on this site and it went exactly as described, fixed it and it sounds like a new dryer. Was going to junk it, glad I didn't!

I won't tell you how we did it, but I'll tell you the right way. Unplug. Remove the exhaust tubing attached to back of dryer. Pry the top up from the front and lean it against the wall. Un plug the wires attached to the front panel (remember where they go) Remove screws at top sides of front panel. "lift up" and remove. Close top. Lay machine on its back. We used a couple of 2x4's to lay it on so as not to crush the vest collar. Clean it out, including lint filter. The new belt wraps around the drum, you will see the channel about midway on drum. Feel behind the motor on the lower right side. There is a shaft with a channel for the belt. Immediately next to that is another pulley type arm with another channel for the belt. This arm moves stiffly and puts tension on the belt when installed correctly. Look at the diagram included with the new belt which shows the path of the belt. Wrap the belt, ridges against the drum and then around the motor shaft. At this point you have to physically pull the last arm out to allow the belt to wrap around the channel provided. If the belt is not twisted , the job is done. Turn the drum with your hands to make sure it is turning properly. Replace the front panel, plug in the electricals, replace the screws making sure the drum is properly centered. Stand up the dryer. Plug in and turn on dryer to make sure everything is right. Replace the exhaust tubing and set into place. Sounds like a lot of steps but I have described the whole process for you beginners. The rest of you will know already. Good Luck . Oh by the way we are 69 and 71. If we can do it, so can you

Door latch or kill switch. Rewarding experience to fix on own.

Unplug the dryer, remove hot air duct. Remove metal dryer back to access thermostat using a nut driver. Unscrew one screw holding on thermostat, detach 4 wires, and replace with new unit, attaching 4 wires to new unit. Then reverse process to button up the dryer. Great how-to video on your site helped a lot!

Unplugged dryer. Removed control panel end caps, removed anchor screw at each end of control panel that had been covered by end cap. Tilted control panel up to access components on back side. Using tech sheet found inside contol panel, swapped motor relay with heater relay (they're identical). Plugged dryer back in, pushed start switch; dryer continued to run (problem identified). Unplugged dryer; replaced relays to original positions. Ordered new power relay (p/n 3405281). Installed new relay when it arrived, plugged dryer in, tested it. Dryer worked normally (problem fixed). Unplugged dryer, reinstalled control panel anchor screws and end caps. Plugged dryer back in. Dryer continues to work normally.

after process of elimination ,figured had to be cut off switch followed simple instructions also watched your video..simple repair up and working again approx. 30 min. once i had kit. thanx 4 the help MIKE

I watched the video several times to make sure I got it right. The first thing that was very helpful was how to disassemble the top cover and front panel using a putty knife to disengage the detents. With the cover off I could acccess the belt and idler pulley. Replacing the belt was fairly easy as long as you note the way it threads through the idler pulley and drive pulley. I thought the video was excellent. It took me right to the problem and the fix. As a bonus the price for the belt was much lower from Parts Supply then from Sears. I've recommended this site to several others.

First I purchased the heating element, still no heat. Then I purchased the thermal fuse,still no heat. I have been pleased with the prompt shipment of the parts and the parts arrived safe. Thank you for service and time, not sure what to do now.I will recommend PartSelect to friends.

Unplug unit / removed back cover / went down , locating both parts to be replaced / simple one screw removal from each part / thermal fuse , one wire @ a time , reinstalled . / Cycling thermostat , 4 wires. Did one wire @ a time , reinstalled. / Putted back cover back on , plugged dryier back up, turned it on to run. To check for heat / yes, ran good as new. Later that day some more running , with damp clothes in it. Did it's job , dry.