11068082700 Kenmore Dryer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Plastic part in door catch was broken so door would not lock to allow the dryer to operate
I tried to remove the part with pliers but could not remove it so I removed the screws that hold the front part of the door. I took the front part off, removed the broken plastic and then lifted on side of the catch so that the bottom of the front part came thru the door and then was able to remove the door latch. The installation of the new part took about 15 seconds to put in by pushing it into the opening where the broken part was removed. I put the front part of the door back and put the screws back and the dryer works fine.
Parts Used:
-
Henri from SILER CITY, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Latch Replacement
Used a screwdriver to pry out the bottom of the latch then the top. Pulled old latch out, then snapped new one in. Super Simple fix.
Parts Used:
-
Kathy from W TERRE HAUTE, IN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door catch broken
-
ROBERT from GAINESVILLE, FL
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lint screen tore and had a side that was loose so it didn't catch all the lint and cut your fingers
-
Wayne from ALBANY, OR
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer won't start.Only make a click noise.
Remove top,front and panels.change thermal fuse and outlet thermistor.
Parts Used:
-
Candido from GREENVILLE, TX
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers, Socket set
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My daughter threw a heavy wet comforter into the dryer and the tri-ring sheared off.
I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.
Parts Used:
-
Joe from St. Louis, MO
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer won’t start
Drum belt broke. Found drive shaft belt guide broke. Replaced pulley wheel since I had it apart.
Parts Used:
-
Kyle from HANOVER, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Socket set
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dryer making noise. order parts
YOU NEVER SENT ME THE PARTS!!!
I had to drive to a parts store to find them. On January 17, 2024, I tried to call you when the parts did not arrive and your recording said there were no reps available and you hung up. WE CANNOT GET HELP TO CANCEL THIS ORDER. We have been going in circles with PartSelect and shipping. SO, how do I get my refund of the $107.26 for the parts that I never received!!
I had to drive to a parts store to find them. On January 17, 2024, I tried to call you when the parts did not arrive and your recording said there were no reps available and you hung up. WE CANNOT GET HELP TO CANCEL THIS ORDER. We have been going in circles with PartSelect and shipping. SO, how do I get my refund of the $107.26 for the parts that I never received!!
Parts Used:
-
Thomas from TULELAKE, CA
-
Difficulty Level:Very Difficult
-
Total Repair Time:30 - 60 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Making a racket.
Took the top off and then front off and drum out . Replaced Drum roller and shaft support bolts.
Parts Used:
-
Carl from MARION, KY
-
Difficulty Level:Really Easy
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rollers making a noise.
Removed the top, removed lower front cover, removed the front, removed the belt, removed the drum and the back. Removed and replaced roller support shaft and drum roller’s. Completed all Front and rear support for drum. Replaced drum , replaced drum roller belt and replaced back, completed replacement of the top, front.
Parts Used:
-
Carl from MARION, KY
-
Difficulty Level:Really Easy
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Pliers, Socket set
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Torn filter seal
-
James from SCOTTSDALE, AZ
-
Difficulty Level:Very Difficult
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Start button failed to keep dryer running; no heat
Dryer is still in pieces after two weeks, dependent upon my time and ability to work on the project. I usually dry my clothes on an outside line, anyway. I especially appreciate Steve's videos demonstrating step-by-step procedures for disassembly, part installation, and reassembly. Very thorough. I timed each presentation---five minutes for one, less than ten for the other. I watched the videos several times and took notes, so I would have the procedures in front of me while working on the unit at the other end of the house, I'm 77, forgetful. When I disassembled my unit, I noticed several rusted areas, so decided not to complete the project until I could get to the store for paint. As a primary care-giver for a severely dementiated 79-year Old Lady, I have to arrange for a relief to go shopping. That's why the machine is still in pieces. Got the paint, though, so back to work---eventually. When I disassembled the dryer, tucked away in the bottom was a very informative TECH SHEET, the discovery of which ticked me off that it wasn't provided with the owner's manual. At the bottom it says, "For Service Technicians' Use Only." In my house, I'm the "...Service Technician...," chief cook and bottle washer, launderer and litter box attendant.
Parts Used:
-
William from APPLE VALLEY, CA
-
Difficulty Level:Easy
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Clothes would not dry
Unplug from electric ? outlet. Set the meter to ohm setting, check part ,no reading. Remove old part ,check new part with meter ,get a reading of 11 or more mA. Install new part and blower cover done.
Parts Used:
-
John from WOODBRIDGE, VA
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
lint screen was not catching lint and sending out the dryer vent
-
Scott from WOODBURY, MN
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Shutting off and had to wait before could turn back on
Followed online video very easy and dryer works like new one....
Parts Used:
-
Allen from KENNETT, MO
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!