1106807811 Kenmore Dryer - Instructions

Unplugged dryer. Removed lint tray screws. Opened top of dryer and removed the two face screws then removed front of dryer. Released the belt tensioner. Then removed the drum. Disconnected the wiring clip and with a creseant wrench held the back of motor and turned the nut in the front clockwise to loosen the motor from the vent fan. Then simply pulled the old motor out and reversed the steps and now have a great working old dryer again.

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

I watched the video that showed how to do the repair. I did exactly what I was shown on the video, and everything worked the very first time ! It was GREAT ! No more squeaking idle pulley !

This is a long, sad story, but I'll cut to the chase. I was told by few appliance repair guys that my problem was most likely due to the motor being bad. I had checked the thermal fuse, the door switch, and the power switch, and all were good so that made sense. I then saw a video which made it seem fairly straight forward to remove the old motor and replace it. So I ordered the motor from Part Select. Turns out it's impossible to remove the motor without also removing (and replacing) the blower. The video never mentions that. Also FYI, I found out that my dryer switch WAS broken, and nothing was wrong with the motor, so I spent $250 on a repair that should have cost %40. Oh well ...

It snapped right in. Works perfect.

I watched the video and after that made the repair, it was very easy and the video was a really big help. From start to finish it took me no longer than 10 minutes.

I watched your repair video and followed what the repair man said and did, it was a snap! I needed my dryer fast so decided to do it myself. I am a 65 year old female and petite, so I say if I can do it anyone can. Your video was the key to my sucess.

removed two screws from filter chute,raised top of dryer and removed front panel,lifted drum out,replace both rollers,replaced drum,reset belt tensioner replace front panel,lowered top,put screws back into filter chute.

Initially thought it was the thermal fuse since that has already been replaced twice before for the same type of problem. After replacing the fuse the same issue remained, so I did a little hunting on the internet and found some matrixes to help diagnose the issue. After a couple of minutes, I discovered it was the ignitor. I immediately ordered the part and received it in about 5 business days. Even though that took longer than previous orders (usually < 3 days), I was still happy to get the part at a MUCH cheaper price than available locally. Installation took about 5 minutes with only a 5/16" nut driver and we were back in business. Kind of glad it broke because the dryer needed a good de-linting and cleaning anyway. : )

Remove the back panel, then remove the housing around the blower, just slide the housing of to the side, you don't have to take it completly of the machine. Remove the top, and remove the front until you can get to the blower motor. Cut the blower wheel plastic down to the metal nut with a fine blade in a recipricating saw, used a bi-directional broken stud remover socket on the nut that was at the center of the blower wheel and large slip joint plyer on the other end of the shaft. Replace the wheel and put back together. It took about as much time to gather up the tools as it did to fix it.,

un plug, gas shut off, nut driver back cover, remove lint screen, slide top forward and lift. disconnect close sensor- front. remove front. remove drive belt and tub. get wife dressed in cookie monster footie pj's to hold motor with wrench while reverse threading fan. remove motor- order from this site, got motor next day. reassemble less than 30 minutes. Impress wife and get lovin!

You have to disassemble the dryer. I looked up how to on youtube.com. I am grateful that people take the time to record the steps in which to do just about anything. Disassembled and ordered motor and fan, damaged fan taking it off, got it in in just a couple of days, installed motor, fan and drum, tested before complete assembly. Works great. Thanks

removed 4 screws. 2 in the back and 2 at the lint screen door. Remove top lid of dryer and looked down and there was the door switch with the broken actuator spring. A diagram of the dryer with part locations is very helpful. I checked the switch with volt meter to make sure it was ok. It was ok! Replace the actuator and put every thing back together and dryer works just fine. Thanks to PartSelect I was able to buy the actuator spring buy itself and not have to buy the switch also.

Removed two small screws on door edge, pop out broken part, insert new part, replace screws. Took 2 minutes 18 seconds. Nice to have various door catches in the Kit. This was a repair on a 1979 Whirlpool Dryer. Great price & service!!

Pulled out old filter. Recycled. Slid in new filter. Closed plastic cover. Voila! Done! No real "repair" involved. More of a replacement.