Models > 11067861600 > Instructions

11067861600 Kenmore Dryer - Instructions

All Instructions for the 11067861600
826 - 840 of 1034
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dryer would not run.
Follow instructions from online video supplied by Parts Select. Repair went very smooth!! Dryer started up and I am back in business. Thank You Parts Select!
Parts Used:
Dryer Thermal Fuse
  • clifton from WESTMINSTER, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!
door switch broke
remove 2 screws from lint vent, use putty knife to remove top op dryer, remove 2 screws holding switch.
Parts Used:
Dryer Door Switch
  • Frankie from Lady Lake, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The timer was working but the dryer would not turn on.
I replaced the Thermal fuse and this fixed the problem.
Parts Used:
Dryer Thermal Fuse
  • Henry from Rosebud, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Socket set
Was this instruction helpful to you?
Thank you for voting!
Dryer wouldn't heat
The video on Part Select didn't actually show my dryer. So I found a video more like my dryer. I took the top of the dryer removed the front panel and removed the dryer drum. I removed the thermal fuse and the three thermostats. I checked each with a multimeter and determined which needed replaced. When the parts came I installed the new parts and put the dryer back together. The dryer immediately worked properly.
Parts Used:
Dryer Thermal Fuse Thermal Cut-Off Kit
  • Anthony from Marion, IL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
no heat
take back from dryer all parts right in front of face replace part and try dryer and it work just like it said
Parts Used:
Thermal Cut-Off Kit
  • henry from sumter, SC
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Socket set
Was this instruction helpful to you?
Thank you for voting!
Dryer Would Heat And Then Stop
I purchased a new heating element installed and stil had same problem. I order the 2 sensor (kit) located in same area and that took care of problem. I should have purcahsed all at same time like someone else told us in the website. Thanks parts select for the very fast delivery
Parts Used:
Dryer Heating Element
  • Terry from Snellville, GA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
dryer would not start and light was not working
unpluged dryer from wall,lifted top of dryer unpluged door switch took out two screws that hold switch, installeed new switch, put top of dryer down, plugged dryer back into wall, very easy repair.
Parts Used:
Dryer Door Switch
  • Randall from Schertz, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Loud sqeaks, noise during drying.
UNPLUG UNIT FIRST!!! Removed back cover. Make sure to note not all screws hold the back cover by closely observing the screw. Take a picture of the belt routing before removing from the idler pulley. Use headlamp or flashlight to light up pulley area. Remove belt from idler pulley by pushing idler assembly towards the right. Use small screwdriver to remove the existing pulley by prying off the existing tri-ring from the back of the pulley. You may have to "feel" the ring since it in facing away from you. Once tri-ring is removed, slide off old pulley and gasket or old second tri-ring. Replace with gasket first, then pulley then tri-ring. Reroute belt. Use picture if needed. Replace back cover.
Parts Used:
Idler Pulley
  • Brian from Redmond, WA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
wont shut off &no light
remove top &replace switch
Parts Used:
Light Bulb - 10W Dryer Door Switch
  • RUSSELL from POUGHKEEPSIE, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Dryer not hot enough
1.Installed thermal fuse. I thought this was the problem as a few years ago this fixed the dryer that was now experiencing a similar problem. Problem persisted. 2. Installed new thermostat. Problem persisted. 3. Installed new igniter coils. Eureka! Problem solved!
Parts Used:
Dryer Thermal Fuse
  • Steve from Buffalo Grove, IL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
No heat
I checked all the thermostats with a OHM meter and found a bad sensor it was pretty simple using U tube as a guide and the parts were here in a day and a half I'm now getting ready to replace the transmission in my GE washer
Parts Used:
Thermal Cut-Off Kit
  • Nicholas from Sylmar, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Gas dryer was not heating.
I ordered the part I suspected....which was indicated by approximately 44% of the users having success replacing the thermal fuse. After watching the video on how to perform the repair, it was a snap! Removed the 9 screws, removed the vent hose, popped out the fuse, and replaced it. After checking to see if that was the problem....which it was, I reassembled the dryer. It only took more time because I chose to vacuum any exposed areas. THANK YOU!
Parts Used:
Dryer Thermal Fuse
  • john from mohnton, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Dryer would not heat.
I ordered kit to your recomendation, took machine appart as per your video (Very helpful), put machine back together only to find that that was not the problem.No other recomendation as to what else I should.
Parts Used:
Thermal Cut-Off Kit
  • Jerry from Gree Bay, WI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
dryer door switch was broken
followed the video you supplied on your web site
Parts Used:
Dryer Door Switch
  • Arthur H from Boca Raton, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
no heat
unplug take off vent hose and back panel unscrew one bolt holding the fuse disconnect 2 wires. Connect the 2 wires to the new fuse hold in place with the bolt put back on the back panel and vent hose plug in and your done
Parts Used:
Dryer Thermal Fuse
  • Juanita from Plano, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 11067861600
826 - 840 of 1034
Back to Top