11067841600 Kenmore Dryer - Instructions

Took off the backplate of dryer, replaced fuse, done.

My way of replacing the pulley was much faster than the parts select video that showed how to replace the belt tension-er pulley. They took off the door, the entire front AND the drum to get to the pulley. I ACCESSED THE PULLEY BY REMOVING THE 4 INCH EXHAUST PIPE, (ONE SCREW) WHICH GAVE MORE THAN ENOUGH OPENING TO REPLACE THE NEARBY PULLEY! I suggest you remake that video

afer looking at the expoled views of the drier and locating the switch i checked to switch operation and found it wouldn't click.i ordered the switch,it arrived in just a couple days(right in the middle of the xmas holidays)i popped the top on the drier after finding 2 screws on the lint screen opening on top,2 screws mounted the switch,reassembled in reverse order and tested the drier.it was easy and with the new part in hand i saved aprox 200.00 dollars fixing it myself. p.s. please unplug the drier before starting any repairs...

there were 5 ,1/4 screws in the back panel . The heater box was right at the rear when the back was removed.. Replaced the two controls that were in the kit with a 1/4 nut driver. Checked the terminals for tightness and contact. No discoloration on contacts. Ran unit after reassembly for 20 min cycle to test ,Put into service

Watched several videos online and was suggested that the thermal fuse was bad, so i replaced it but no fix. So i checked the previews Q&A from other costumers and watched the videos on how to replace different parts. I first looked thru the peep hole on the bottom left part of the dryer and saw the igniter glow for about 10 sec every minute but no flame would start. So i replaced the igniter, the flame sensor, and the coils all at once. I know thats not the proper way to troubleshoot something but i was gonna take the drum out and everything so mind as well replace them all. Dryer works like new and dont have to listen to the wife complaint anymore!!!

Took the back cover off. Replaced fuse and put the cover back on. Worked great.

After reviewing a variety of online instructional videos I was able to figure out how to remove the top ("hood") panel of dryer to access the door switch. Once I had access the switch was relatively simple to replace.

Dryer is on a pedestal. Opened drawer and removed two 1/4 inch screws on bottom panel of dryer front. Panel drops down and exposes the dryer exhaust where thermistor is located. Removed two spade connector wires and removed two 1/4 inch screws. Installed new thermistor and reversed procedure. For the moisture sensors I used a phillps screwdriver and stuck my head in the dryer and removed the lint screen assembly (3 screws). Removed the spade wire connectors and used a straight blade screw driver to remove the moisture sensor. Installed the new sensor and re-installed the lint screen assembly in the reverse of removal. All very easy - just took 30-45 minutes total.

Watched steve on the video on changing the thermistor a couple times, it appeared to be straight forward replacement. Unplugged the dryer. . . Went through the front, my lent filter slides in and out from the lid so I had too remove two extra screws to detach it. After opening up the front it became very apparent my thermistor was not located in the same location as the one in the video. Dryer needed a cleaning (lint/dust) so I released the idler pully tension on the drum belt and went ahead and removed the drum/belt and shop vac/ blew with compressed air and shop vac once again. Gave my dryer a much needed cleaning since I had it apart. Put everything back together in about 20 mins. Pulled the dryer away from the wall and removed rear cover and presto there it was right next to the dryer air outlet. Replaced thermistor and replaced back cover, inspected out flex hose on dryer outlet, I clean it out (flex) yearly to prevent problems. Reattached flex on both ends, re-positioned dryer, plugged back in, and works great! Definitely fixed my problem. . . Replacing the drum by myself was a bit difficult. Still do able (there's a video on that also. . )

I ordered the Thermal Fuse, as it appeared to be the problem. A friend suggested that as long as the price was fairly reasonable, I should go ahead and get two of them and keep one for later. I ordered/paid for two of them. I put the Thermal Fuse in, and when I attempted to turn the dryer on, it ran for about 5 minutes, at a very hot heat, dried the towels, and then would not come on again. I thought it had kicked the circuit breaker, but after checking, found it hadn't. I watched the youtubes.com again and found that there were three other parts that it could possibly be. I ordered them, and replaced all of them. One of them had 4 prongs but two on the new one. I left two wires off, and sure enough, it would not run. I borrowed an ohm meter, and found out my old part was still good, but that in the process it had blown the Thermal Fuse, of which I just happened to have an extra, and after installing it, it is now in perfect running order. The total repair was about $80-100, rather than a $75.00 bill for service and heaven only knows for the parts at the repairman's price! Thanks youtube, Parts Select and my friend for his advice! Walter

My front- loading dryer is 4 years old and lint screen felt liner never lasted long without falling out. When I received my Part Select I knew the quality surpasses manufacture screen. It is so much better and we are your new customers forever Thank you Cheryl

I just followed the instructions on the video. The only helpful addition I have...make sure the power is off before you start. I did get that point when the video said to turn the power back on, at the end of the video. In all...a great experience and I saved more than $200.00 doing it myself, with the help of the FANTASTIC web site at PartSelect!

I repaired this dryer after I did a little research online to learn about the thermal fuse. I took the back off the dryer and used the Fluke meter to test the thermal fuse for continuity. There wasn't any. I left the dryer disassembled and ordered the part. It arrived two days later. I installed it and reassembled the dryer in just a few minutes. It was a pretty simple repair.

took out the fabric softener cup pull out diaphram unscrewed the bolt pull out the cup replaced with new parts I want to thank you for your fast service. it is awesome. i will recommend you to all my friends.

1. Shut off power to dryer 2. Remove back panel covers with 1/4" nut driver 3. Use ohm meter to determine continuity at various thermal couples (3) and the one thermal fuse on the blower panel. . (This was the "bad "one in my case) 4. Remove two wires and remove the one screw that holds fuse. Did not have the model# for dryer, so I took the part# from the blown fuse and found it at partselect. Com. . They even showed an exact picture of the part I needed. . Ordered on tuesday/arrived by fed x on saturday. . . Reverse procedure to install. .