11067732790 Kenmore Dryer - Instructions

It snapped right in. Works perfect.

I watched the You Tube video on this site. The only issue is there is a plastic fitting that I seriously damaged trying to remove the motor from the blower. You have to hold the plastic fiting stationary while turning the nut on the other end of the motor. If you try to rotate the plastic fitting you'll destroy it as I did. I got it loose by squeezing the plastic fitting with a large pair of channel lock pliers and then rotating the nut.

I was able to take apart the dryer myself and get old belt out, then my son helped me remove the drum and put new belt on. Well worth fixing; it works great again and the part with shipping and handling was only $17.00! better then price of new dryer!!!Thanks, Mary ( Cincinnati)

my son replaced the door switch and that was it works great

Initial diagnoses suspected a faulty igniter. After deterininig that there was not power to the igniter I unplugged the dryer and systematically tested the continuity of each of the temperature limit swithches which all checked OK. The last item in the circuit is the thermal fuse which proved to be faulty. To confirm that this was the only problem I monentarily by passed the fuse to verify that the burner came on. To do all this I had to remove the fron panel and take out the drum. Actually the thermal fuse is located behind th back cover and is very easy to replace and probably should have been my fist go to suspect. Note the likely cause of the thermal fuse failure is a plugged up lint filter or exhaust duct which should be checked before installing a new fuse.

Removed top, Face and pulled the tub out. Blew out all the dust and lint. Cleaned and lubed tensioner, installed new tub plastic bearing and reassembled.

replace with new element since I had the back off. Might as well do high limit and tstat. Since the dryer belt was very old I decided to replace it also. The repair was very easy since the parts matched perfectly.

looked at schematic diagram, compared to unit finally used a multimeter to check fuse.. replaced fuse, assembled dryer and turned on to check operation. OK.

Repairing my dryer was one of the easiest things I have ever done and saved me quite a lot of money. The hardest part was getting the bolts out, mainly because I used pliers instead of the tool needed for the bolts in hard to reach places. I watched a video online on how to replace the parts, ordered the parts needed for my model, and repaired it myself in minutes. I replaced the heating element, both thermostats and the Thermal Fuse. I have very little time and money invested and my dryer works perfectly.

We have a 20 year old Whirlpool dryer and it stopped heating and drying. I searched online for causes and linked to this website. The problem list recommended the heating element replacement. I checked a local appliance store and they had the element for $91.00. I quickly ordered the element form the web site for half the price delivered. Not being too handy, I watched the installation video, grabbed my nut driver set and headed to the laundry room. The back came off in minutes and I was able to swap the element in about 5 minutes. I put the back on and tested...no heat. Back to the website and I ordered the next likely part, the thermal fuse. A day later the part arrived and another 15 minutes later I was again testing the dryer...no heat. Back to the website and ordered the Thermal cutoff kit and cycling thermostat. They arrived the next day..in fact I just got done fixing the dryer. First I replaced the cycling thermostat, no go. Then I replaced the high limit thermostat, nothing, then the thermal cut off fuse, and voila, heat in the dryer. Always start with the last part you would replace (always the way). I spent around $100 including shipping and although others may have been able to find it sooner, I now have a new heating element as well as all the other heat related parts. I probably saved a few hundred dollars bringing in a technician to fix this. I would recommend Parts Select to anyone with this or other appliance issues. Great website for the experienced DIYer or novices. Thanks Parts Select!

went on-line to research the problem. found the site and listed the issue. agreed with the probability and ordered the part. it came in a few days. After I ordered the part I watched the short instructional video that was available from the site. the repair took about 10 minutes to pull out the dryer, remove the back, take off the old part and put on the new part - put the back on plugged it in and push it back then turned it on. DONE

Checked motor and other components and found Thermal Fuse did not check out allowing voltage to motor. Replaced Thermal Fuse and Dryer worked

the only thing i do around the house is changing the light bulb, so when our dryer was not working and was about 5 years old, i was told it cost too much to repair and i am better of to get a new one so watched few clips on you tube and ordered the parts from partselect which came with instruction, i could not believe it spend about $100.00 and my dryer is working better than before. bottom line if i can do this anyone can.

I watched the video and after that made the repair, it was very easy and the video was a really big help. From start to finish it took me no longer than 10 minutes.

the part came the day after it was ordered.this was a shock,i opened the package and watched the video for the repair on my laptop.the instructions were right on and the job went smooth.thankyou for saving me over 400.00 on a new dryer