11067342700 Kenmore Dryer - Instructions

I followed instuctions, also watched a how to vidio, had a little problem reinstallig front cover. The job took a little over a hour. The squeel was coming from old style belt tensioner.

I followed exactly the video. It really was that simple. My 5 year old even helped me unscrew the nuts. The Thermostat was on the lint shaft and unscrewed easily. Once out I removed the wires. The hardest part was removing the wires, They were really tight. I replaced the wires and screwed in the part. Before I replaced the back I cleaned out the lint tube and turned on the dryer. I saw the flame and the heater kicked right on. I replaced the back and was done. *****However the next time the dryer went the heat didn't remain on and turned off too soon. I did some more research and found you usually need to replace the thermal fuse at the same time on Whirlpool units. So I have ordered the part and will let you know if kept the heater from turning off too soon.

Learned that my Kenmore dryer was actually a Whirlpool model. Removed kick plate in front of dryer. Removed the cover to the blower wheel. Cleaned out Dryer with vacuum cleaner. Used a multimeter to check for continuity on all thermostats, fuse, and heating element. Decided it was the cycling thermostat. When ahead and replaced the fuse at the same time. Checked out the installation video on this site, wwwPartselect.com ( it was very helpful in understanding how to remove the cycling thermostat - needle nose pliers helps in pulling of the connect wire clips - knuckle buster). Ordered next day delivery. The parts were on my front door early next morning FEdEX ( i live in the very corner of the NW US). Nice!

(Always unplug dryer before making any repairs) I opened the dryer and checked the heating element. Making sure that the connection was good and nothing was damaged, I determined the problem was overheated wires. They melted and lots connection. I replaced them with the heating element wire connection kit. Easy to install and simple to get right. I cleaned the dryer again with a vaccum cleaner, removing all the lint, and checked the vents, making sure they were clear...I turned the breaker on (it was tripped when the dryer overheated)and everything worked great.

The video you had of my dryer was different then my dryer and the pulley was in the middle of the bottom and the motor and fan were in front of it. I had to replace the belt without being able to see what I was doing. I couldn't get it at first then realized there was tension on the pulley wheel and had to pull it towards the other wheel in order to get the belt on there. Once I pulled the wheel it went on really easy. My first time working on a dryer but I knew I could do it myself.

instructions were clear and repair was easy

Well, to Figure the issue I took the entire thing apart. Actually a lot more than needed. I found the torn belt and ordered it. I did not realize I may need a new belt tensioner which is sold with a wheel for the belt to wrap around and be tensioned by. Actually the original just utilized a rubber c or u shaped design(no wheel) for the belt to slide over. Anyways, instead of ordering and waiting for a new wheeled belt tensioner, I installed new belt with all original parts and working fine. I did oil up the drum rollers to reduce noise. And since I took the whole thing apart I cleaned the lint from every place it could hide. Ps a coke can is said to be helpful to hold the drum up while installing the belt but I found a jug of laundry detergent did better. Totally easy project for someone with no appliance repair history

The broken belt was found when I opened the dryer. The part number was on the belt and a quick online search led me to PartSelect. The part was available, delivered in less than 2 days and there was an online video showing the entire repair in detail.

My ground wire in my electrical box was not connected.

removed access panel installed new switch reinstalled access panel

Pull lint screen, remove two phillips screws,pry top front up and hinge back,remove two screws at top inside, unplug door switch, lift front and remove, remove drum. Read instructions,install new parts, reverse above dis-assembly, happy dying.

Replaced Broken Belt and roller

Replaced the Drum Roller, Belt, Belt Tensioner and Rear Drum Seal by watching the video that was attached with the order form from PartSelect. Removed screws from lint filter, raised the top by sliding it forward a small amount, able to raise top and leaned it against a wall. Then removed two screws from front panel and lifted front up slightly while holding the drum and removed it from front of dryer and placed it out of the way. Loosened the tensioner pulley to remove the belt and once that was done pulled the drum out and replaced the drum rollers (by looking at the video). The rear drum seal was the most aggravating part in getting it off and cleaning it up. Was a little messy putting it back on and then just reversed everything to put it back together. It is working properly now. Thanks to the video. PartSelect parts came earlier than I expected they would and I appreciated that very much.

It took longest to take apart and test to see which part was bad. I had never done it before. Got it apart and used the drawings on Parts Select to find location of parts. Testing only few minutes found bad thermostat.Ordered parts, and they came in 1 1/2 days. I replaced both thermostats being they were in the kit. Actual repair took maybe 15 minutes. Vacuumed out everything I could. Took lint trap out a vacuumed. Put it back together, plugged it in, heated like new. All time told I would say little over hour.

Ordered entire Maintenance kit - good call because it was the tensioner pulley that failed and cut the belt. To replace, had to raise the top (2 screws in lint screen slot)and pull the entire front off (2 screws - 1/ea on top inner edge of front door panel then lift it up and out) Replaced both rollers, then used the parts kit shipping box to prop up the front of the drum while installing the belt and tensioner pully. Re-assembled in reverse order, works fine.