11067332600 Kenmore Dryer - Instructions

removed access panel installed new switch reinstalled access panel

Pull lint screen, remove two phillips screws,pry top front up and hinge back,remove two screws at top inside, unplug door switch, lift front and remove, remove drum. Read instructions,install new parts, reverse above dis-assembly, happy dying.

Replaced Broken Belt and roller

Replaced the Drum Roller, Belt, Belt Tensioner and Rear Drum Seal by watching the video that was attached with the order form from PartSelect. Removed screws from lint filter, raised the top by sliding it forward a small amount, able to raise top and leaned it against a wall. Then removed two screws from front panel and lifted front up slightly while holding the drum and removed it from front of dryer and placed it out of the way. Loosened the tensioner pulley to remove the belt and once that was done pulled the drum out and replaced the drum rollers (by looking at the video). The rear drum seal was the most aggravating part in getting it off and cleaning it up. Was a little messy putting it back on and then just reversed everything to put it back together. It is working properly now. Thanks to the video. PartSelect parts came earlier than I expected they would and I appreciated that very much.

It took longest to take apart and test to see which part was bad. I had never done it before. Got it apart and used the drawings on Parts Select to find location of parts. Testing only few minutes found bad thermostat.Ordered parts, and they came in 1 1/2 days. I replaced both thermostats being they were in the kit. Actual repair took maybe 15 minutes. Vacuumed out everything I could. Took lint trap out a vacuumed. Put it back together, plugged it in, heated like new. All time told I would say little over hour.

Ordered entire Maintenance kit - good call because it was the tensioner pulley that failed and cut the belt. To replace, had to raise the top (2 screws in lint screen slot)and pull the entire front off (2 screws - 1/ea on top inner edge of front door panel then lift it up and out) Replaced both rollers, then used the parts kit shipping box to prop up the front of the drum while installing the belt and tensioner pully. Re-assembled in reverse order, works fine.

just replaced the rollers with the new ones. The trouble was getting the belt around the drum again, but it all worked out and the dryer is running good

I went to partselect.com, input my model number and problem, I clicked on the right solution and watched a short video on how to repair the problem. Ordered the parts which arrived the next day. It took me ten minutes to replace the two parts I had ordered and the problem was solved. I probably saved a couple hundred dollars doing this repair myself..

Replaced Thermal Fuse

Your website was wonderful--thank you so much! When I saw that 47% of the time this was the problem, I ordered it & it worked! This was a life saver for me! I will come back to this site anytime I have an appliance problem! Thanks again!

I would like to thank the people who created this site. My husband recently passed away from stage 4 esophageal cancer. We only knew he had it for five weeks before he passed. With the medical bills he left behind, I really could not afford to buy a new dryer or hire anyone to fix mine. I do not remember how I found Parts Select but I'm thrilled I did. I first used an ohm meter to find the defective part. Then I followed the step by step video and was able to completely fix my dryer in about an hour. Changing the connectors on the thermal cut-off was a bit of a challenge for me but I managed. I also changed the switch on the door which allows the dryer to shut off when the door is opened. I am truely grateful for this site and will highly recommend it to all my friends and family.

I went to parts select website to find out how to repair it myself because when I took the heating coil off I could tell just by looking at it that it was not broke or cracked in anyway so I went to the website to get an idea of how to start diagnosing were the real problem actually was and I found everything I needed from step by step instructions to diagrams and symptom diagnosis and actual pictures of the parts themselfs.

took the top and front off the dryer and had to route the new belt around the drum and through the pulleys, it was really easy and a heck of a lot cheaper then buying a new dryer

Called PartSelect, gave them the make and model number of the dryer and told them I needed a new belt for it. They gave me a price including shipment (under $20.00). I oreder the new belt and it arrived within a week. I also got an e-mail from PartSelect with a video showing how to replace the belt. This was very helpful. I was able to watch the video, take the dryer apart, replace the belt (after a few tries), and put the dryer back together. Problem solved! Thanks PartSelect.

I replaced the thermal fuse and the cycling thermostat, it was quite easy you need a 1/4 nut driver and remove the back of the machine and the two items are there in plain view simply remove and replace and voila,I am a woman with more knowledge of how things don't work when broken but laundry was going to pile up and I was desperate and couldn't afford to call a repair man and the husband doesn't fix things he doesn't use and he was planning on stringing clothes line throughout the house to remedy the problem :( it took me about 45 minutes but that included finding anything I might need and vacuuming and cleaningthe dryer and vents had I called a repairman I may have ran off with him ;) felt amazing when I turned it on and it worked perfectly!