11067332600 Kenmore Dryer - Instructions

I ordered the part, watched the video and made the repair in less than thirty minutes. This was much cheaper than purchasing a new dryer.

Took the back cover off the dryer and replaced the heating element with the new one put the back on connected the vent hose and done . Have smiles now, saved money.

Pull off the front panel of the dryer, and replaced the thermal fuse. Very easy. Plus, vacuumed out the whole inside of the dryer, the rear and the tube running from the dryer to the outside. Will be doing this at least every 3 months to be safe. You would be surprised at how much lint builds up inside the machine. Eve though we clean the filter trap after every use of a load of clothes.

Repair went fine. Really easy for the most part. Unfortunately it didn't solve my problem. Great place to get parts though. I'm going to continue my search for the source of the noise

Thank you for the the installation tip I received along with the part. The suggestion of removing the front panel to install the belt made the installation go very smoothly.

I unplugged the dryer then removed 2 Phillips screws from lint trap. Then I popped the top up on each top corner with a screwdriver. I removed the 2 screws holding the front cover. I unclipped the wiring connection and moved the panel. I took out the old belt, put the tensioned back on then put the new belt around the drum and held the drum up with my shoulder then put the belt through the tensioner and put it on the motor spindle by pushing the tensioner back. I put it back together and it worked perfectly. Your video was very helpful. Job was very easy.

Had my wife call the repair man. Since it was Saturday afternoon, no luck. YouTube help me diagnose the problem. I found that the drum belt slipped off the idler pulley assembly and the assembly was laying on the floor. I noticed that the belt was frayed and was probably stretched out which may be why the belt slipped off in the first place. I glued the frayed pieces of the belt back with gorilla glue and clamps. You Tube helped me mount the idler pulley assembly and string the belt correctly. I then ordered the replacement parts through your website. The parts came to my home in a few days and I will fix the dryer properly when I get a chance.

The instruction sheet that comes with the parts is excellent. Follow it and all goes well. Be patient and stay away from the sharp sheet metal edges present in all such appliances !!

First bought the Cycling Thermostat and Thermal Fuse. Installed. Still did not work.Next bought the Thermal Cut-Off Switch and the High Limit Thermostat. Installed. Still did not work. Then purchased the timer and installed. Still did not work. Finally tested the heat element with an on/off switch and wire. The heater worked. Changed the 2-pole 30 amp switch in panel box and the problem was solved. The parts were reasonable and easy to install. I left the new parts in and saved the old oned for the future, Parts delivery was quick. Will use parts Select in the future.

Watched the video and followed the directions. It was pretty easy, but, I ended up having to call the repairman anyway. After the heating element was put on we put the cycling thermostat on. I didn't know it, but I put some wires on upside down. I bought a heating element, a cycling thermostat, thermal fuse, and a thermal cut off kit. All that, and I still had to pay a repairman. If you're good with wires, or have some knowledge of appliances this is an easy fix.

Diagnosed problem , orders parts . Installed parts

I watched the video on this site and it went exactly as described, fixed it and it sounds like a new dryer. Was going to junk it, glad I didn't!

PROBLEM: Intermittently, the dryer would not advance on the Auto Dry setting and would stay at max heat continuously, even after 2.5 hours with the clothes dry and very warm. At first, I replaced the CYCLING THERMOSTAT, which DID NOT correct this issue. Then I also found the 60 Minute Timed dry setting would work fine until the end of the cycle and the dryer would stop like it should. Then, I checked back 10-15 minutes later and found the timer had advanced into Fluff Dry Timed cycle with heater on full, but the dryer not moving air. This caused the Thermo-Cut switch (fuse) off to open and the Heater Element would not put out enough heat to dry the clothes. TROUBLESHOOTING: 1- UNPLUG the dryer for all troubleshooting and set the DVM for OHMS ( or use ohm-meter). 2- Both the Cycling Thermostat and High Limit Thermostat checked good at 0 ohms (dryer unplugged). The entire Thermo Cut-off/Thermostat circuit can be checked at the Timer (VERIFY proper wire color with dryer schematic in top console), which also verifies the wires are good and should be 0 ohms without the Heater Element in the circuit. For the Whirlpool WED5300SQ0 dryer, it's the Red and Orange wires at the Timer. 3- If the Heater Element is in the circuit (see schematic for test points), look for between 8-12 ohms for a good Heater Element. For the Whirlpool WED5300SQ0 dryer, it's the Red and White/Black wires at the Timer or across the Heater Element connection. SOLUTION: The Heater Element checked out good at 10 ohms. When the Heater Element was physically removed from the dryer one of the PORCELAIN MOUNTS was BUSTED, which caused the heater element coil to intermittently come in contact with the dryer housing while running/drying clothes, which caused the Timer to not advance on Auto Dry when the Cycling Thermostat Opened and malfunction for the Timed Dry settings. To physically check the Heater Element, just remove the 2 screws and the wires to the High Limit Thermostat can stay hooked up. The Thermo-Cut off kit is easy to install and there is a installation video if there are questions. Just be careful to NOT cut the Heater Element connector on the Jumper wire kit. The spade connector for the heater element is wider than the other side that is cut off for the dual spade connector. The Heater Element is easy to replace as well. If the Thermo-Cutoff Kit is being installed, the new High Limit Thermostat can be mounted to the new Heater Element before it is mounted to the dryer housing, which makes it easier to screw in the self-tapping screws. After this repair was completed, dryer has functioned perfectly after many loads of clothes using all dryer settings.

I was pretty sure it was the heating element. I watched two different Youtube videos. Once I cleaned up all of the trash and coins behind the dryer, it was just a matter of removing the screws from the back. I disconnected the wires, replaced the element, and reconnected everything and replaced all of the screws. It works perfectly again!

I won't tell you how we did it, but I'll tell you the right way. Unplug. Remove the exhaust tubing attached to back of dryer. Pry the top up from the front and lean it against the wall. Un plug the wires attached to the front panel (remember where they go) Remove screws at top sides of front panel. "lift up" and remove. Close top. Lay machine on its back. We used a couple of 2x4's to lay it on so as not to crush the vest collar. Clean it out, including lint filter. The new belt wraps around the drum, you will see the channel about midway on drum. Feel behind the motor on the lower right side. There is a shaft with a channel for the belt. Immediately next to that is another pulley type arm with another channel for the belt. This arm moves stiffly and puts tension on the belt when installed correctly. Look at the diagram included with the new belt which shows the path of the belt. Wrap the belt, ridges against the drum and then around the motor shaft. At this point you have to physically pull the last arm out to allow the belt to wrap around the channel provided. If the belt is not twisted , the job is done. Turn the drum with your hands to make sure it is turning properly. Replace the front panel, plug in the electricals, replace the screws making sure the drum is properly centered. Stand up the dryer. Plug in and turn on dryer to make sure everything is right. Replace the exhaust tubing and set into place. Sounds like a lot of steps but I have described the whole process for you beginners. The rest of you will know already. Good Luck . Oh by the way we are 69 and 71. If we can do it, so can you