1106707300 Kenmore Dryer - Instructions

Took the old one out and replaced it with the new one.

I had to take the top loose and raise it up. There are two screws in exhaust vent you have to take out then you can raise the top. When you raise the top you will have to take the front loose and open it up enough to take the drum out. Go to the back and take the lower cover off and take the screws holding the exhaust vent out so the vent will come out the top. When you take the vent out you will see a fan on the end of the motor shaft. The fan is threaded on the shaft and it is left handed threads. As you face the fan you will have to turn the fan to the right to get if off. You will need someone to hold a back up on the motor shaft inside the dryer to keep it from turning. Take the motor out then get the new motor and wire it according to instructions. Install the motor on the motor mount, put fan on then put everything back in reverse order that you took it apart. The hardest part for me was putting the clips on the motor when I put it back together. Hope this helps you.

Had to guess at replacement (dryer too old to still be listed) picture and measurements looked right; it was, Old one out--new one slid in, great that it was available.

Unplugged dryer. Removed lint tray screws. Opened top of dryer and removed the two face screws then removed front of dryer. Released the belt tensioner. Then removed the drum. Disconnected the wiring clip and with a creseant wrench held the back of motor and turned the nut in the front clockwise to loosen the motor from the vent fan. Then simply pulled the old motor out and reversed the steps and now have a great working old dryer again.

I watched the video that showed how to do the repair. I did exactly what I was shown on the video, and everything worked the very first time ! It was GREAT ! No more squeaking idle pulley !

This is a long, sad story, but I'll cut to the chase. I was told by few appliance repair guys that my problem was most likely due to the motor being bad. I had checked the thermal fuse, the door switch, and the power switch, and all were good so that made sense. I then saw a video which made it seem fairly straight forward to remove the old motor and replace it. So I ordered the motor from Part Select. Turns out it's impossible to remove the motor without also removing (and replacing) the blower. The video never mentions that. Also FYI, I found out that my dryer switch WAS broken, and nothing was wrong with the motor, so I spent $250 on a repair that should have cost %40. Oh well ...

It snapped right in. Works perfect.

I watched the video and after that made the repair, it was very easy and the video was a really big help. From start to finish it took me no longer than 10 minutes.

I watched your repair video and followed what the repair man said and did, it was a snap! I needed my dryer fast so decided to do it myself. I am a 65 year old female and petite, so I say if I can do it anyone can. Your video was the key to my sucess.

My wife did the repair. Went on your website and watch the video on how to replace the switch and she was able to do it herself. I didn't mind at all. Saved $75.00 service charge.

I followed the instructions from your sight mainly with a alteration.

removed two screws from filter chute,raised top of dryer and removed front panel,lifted drum out,replace both rollers,replaced drum,reset belt tensioner replace front panel,lowered top,put screws back into filter chute.

Remove the back panel, then remove the housing around the blower, just slide the housing of to the side, you don't have to take it completly of the machine. Remove the top, and remove the front until you can get to the blower motor. Cut the blower wheel plastic down to the metal nut with a fine blade in a recipricating saw, used a bi-directional broken stud remover socket on the nut that was at the center of the blower wheel and large slip joint plyer on the other end of the shaft. Replace the wheel and put back together. It took about as much time to gather up the tools as it did to fix it.,

un plug, gas shut off, nut driver back cover, remove lint screen, slide top forward and lift. disconnect close sensor- front. remove front. remove drive belt and tub. get wife dressed in cookie monster footie pj's to hold motor with wrench while reverse threading fan. remove motor- order from this site, got motor next day. reassemble less than 30 minutes. Impress wife and get lovin!

You have to disassemble the dryer. I looked up how to on youtube.com. I am grateful that people take the time to record the steps in which to do just about anything. Disassembled and ordered motor and fan, damaged fan taking it off, got it in in just a couple of days, installed motor, fan and drum, tested before complete assembly. Works great. Thanks