11067042600 Kenmore Dryer - Instructions

ordered new lint screen, removed old screen, inserted new screen.

After a few years of slamming the dryer door (at least that is what my husband says), the catch on the dryer door broke. Using pliers (I used needle nose) squeeze the outer edges of the catch together (vertically). With it compressed, it should slide out easily. My husband had jacked with ours prior to the repair, so the broken piece in the door was actually sideways and would not fit through the hole. Using a screwdriver, I pushed that piece into the door (it lives in the door somewhere now). I was then able to slide out the rest of the old catch. Compress the new catch and insert it into the hole in the door. Push it in until it clicks into place. DONE! Happy Drying!

Found this site by googling, and it works! I searched lint filters and just ordered based on how it looked...LOL! Husband wasn't home, it looked pretty much like the one I had in my hand, so.... I ordered it. It is the perfect fit and seems to have a tighter gasket glued in all around the screen. Let's hope this one lasts longer than 6 months! Thank you Parts Select for being so fast!! Filter got here in less than 48 hrs.!

Removed the back of the dryer taking off the screws. Found the disposable thermal fuse. Unplugged the 2 blue wires connected to it. Removed the screws holding the part in. Replaced the old part. Reattached the blue wires. Put the back on the dryer. And voila! That simple!
I'm a 39 year old woman with absolutely no patience for tedious jobs, but this was so easy I felt good about doing it. And felt even better for saving lots of money by doing the repair myself.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

The repair was fairly easy. The most timely part of the repair was removing the twelve screws from the back panel to expose the repair.

took off about 8 screws, opened door into it's front & back parts, popped out the old/broken door catches and re-inserted replacements. Only 1 is needed, but this is the 2nd one to break. The first time a repairman switch the un-used from right side to left. (there are 2 so the door can be hung left or right opening)

Had to remove the back of unit to access the area of subject part by removeing 12 to 14 screws also the gas line had to be removed. Two screws held the part in place. Unit now runs normal.Saved alot on repair costs!!!!!

Removed old filter and put in new one.

Replaced

After unplugging the dryer, I removed the bottom panel in front. Remove the the filter inside the dryer and remove the filter housing below. There you can see the thermal fuse on the air duct, its white with two blue wires. You can check it with a ohmmeter after removing the wires. If its open its bad. Its held in place with two sheet metal screws. After replacing the thermal fuse the dryer worked fine. However I would suggest cleaning the air duct and the outside discharge opening. Hope this helps.

I tried to follow directions followed by others on this site after diagnosing the problem via suggestions provided by users. I have a Whirlpool Duet dryer from 2002. We've had problems since moving about 3 years ago. I removed the front panel (lower) by unscrewing the two bottom screws (1/4" sheet metal screws). Then I took out the lint screen and the metal tube/contraption immediately beneath to get access to the area where thermistor is located. See the drawing/chart to help you locate this. It's really easier than it seems. Make sure you have the chart/drawing for your model - it makes difference! The thermistor came out pretty easily with a nutdriver that has a swivel offset shaft. Ask your hardware store tool dept. about that one. Put everything back in reverse order of course and test either with/without the front panel re-attached. In my case it fixed at least part of the problem. I was able to get clothes almost dry with most settings but I have yet to install the moisture sensor to see if that helps in addition to the internal-bias thermistor. I am the kind of person that does one thing at a time so at least I now know the thermistor was bad. Good luck and hang in there with your own repair. It's a lot cheaper even if it takes you longer to do than a pro.

the job would have gone faster if the right parts had been sent in the first place. I would have never paid for two day shipping. In the repair, I removed the rear panel, clipped the plastic triangle holding the bearing, installed the new bearing and new clip.

Took the old filter out and inserted the new one- works great!!

Remove bottom panel was able to remove the element from the bottom without taking off the whole front and removing the drum simply remove the panel remove the two wires connected to the coil unbolted the bracket that was held on by two small bolts then removed the 4 bolts holding the bracket together was able to remove the heating element and then put everything back together did not have to remove the drum the top or the back panel To complete the repair I am not an appliance repair technician just a homeowner but I was still able to repair this myself and it’s working just fine