Models > 11066862500 > Instructions

11066862500 Kenmore Dryer - Instructions

All installation instructions for 11066862500 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11066862500
1,771-1,785 of 1,876
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer was clunking very loudly

  • Customer: Jim from Huntington Beach CA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed instructions that came with the dryer with the exception of the idler pulley which I didn't install because this maintenance kits idler pulley does not match my dryers. Not even close. I would have had to cut or drill holes to make it work. Since I knew it was the rollers that were the problem. Dryer worked great once I was done, but it probably would have been cheaper for me to order the parts individually without the Idler Pulley if I wasn't going to replace one.

Broken drive belt

  • Customer: Antrhony from Warwick RI
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Removed back cover,top,lower and upper front,and drum. Cleaned dust and dirt drom all of the removed parts and then removed the "lint tube". Took the tube apart to clean out dirt and lint, cleaned the lint off of the motor and blower wheel, and then removed the support wheels. Installed the "lint tube" and then the new support wheels with the new locks and then installed the new belt onto the drum. I had to support the drum in order to correctly line up the belt, and then installed the upper front panel. plugged in the power cord and started the motor to be sure everything was OK before closing up the rest of the cabinet. All was OK and the belt tracted perfectly. Installed the lower front panel, top, and the rear panel. Installed the gas connection, checked for gas leaks and installed the dryer back in place. checked operation with a batch of wet clothes and the dryer worked "better than new"!!! The instruction sheet was "spot on" for clarity and accuracy.

Loud squeaky that turned into a rattling noise

  • Customer: Andrew from Chimacum WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched your video that showed me how to remove the top then the face of the dryer. I then removed the drum and belt,after which I could then remove the support wheels and the belt tension wheel.I replaced the support wheels and tension wheel,the hardest part was removing the little plastic locking keepers that hold the support wheels in place. After that I was able to reinstall the drum with the new belt and reinstall the face and top of the dryer. My 15 year old dryer works great just like new. Thanks

Belt on dryer replaced

  • Customer: William from Lakeland FL
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The instructions were easy to follow and the pulley on the replacement part was evenbetter quality than the original. I also followed the recommendation to clean the lint trap. Now the dryer works quieter and better than it ever did. Thanks for your product!

Loud "squacking, squeeling noise" during operation

  • Customer: Jon from Hernandez NM
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Found right parts for problem on this website. Handyman took down machine and installed the drum support wheels. Taking apart was not too difficult; getting drum and dryer face aligned properly was a bit difficult and took longer than expected (and 3 of us). However, it was much better than having to buy a new dryer, since there was very little really wrong with this one. BTW, it was "out of warranty" so it would have cost around $150-$250 to repair using the repair service from the retailer we bought it from. Saved lots of money. Thanks.

Squealing noise during drying cycle

  • Customer: Anthony from Carolina Shores NC
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Repair was as straightforward and simple as the videos implied. The most difficult part of the repair was disconnecting the door wiring. It could be more plainly shown in the videos. After that it was simple. The cleanup inside the dryer, lint, etc., took as long as the repairs. An extra set of hands to hold the drum in place while routing the new belt over the drive pulley would have made it even simpler. Runs like a new dryer now.

Broken belt

  • Customer: kevin from rippley WV
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Very detailed instructions.

The dryer sounded like a herd of buffalos running by.

  • Customer: Patrick from Bettendorf IA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I needed to replace our drum support rollers - one was completely worn out and wobbling (the buffalo herd noise) the other wasn't too bad, but for an older dryer(15+ years) I figured it was time to replace both wheels. I ordered the maintenance kit that also included the Idler Pulley and drum belt. I spent most of my time with the vacuum since there was a lot of dust accumulated inside the dryer. (I recoverd $1.83 in coins!) The instructions that came with the kit were very helpful for this repair. Plus, there were some online videos that heled as well. Once I had everything apart I noticed the plastic bearing ring on the drum's front was nearly worn out so I quickly ordered this from PartSelect and it arrived quicly in two days - this took only 10 minutes to replace.

drumbelt broken

  • Customer: David from N Chelmsford MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Used a ropeasround the dyer drum to simulate thebelt to peload the idler This allowed me to get the belt over the motor shaft without the idler sping tenion causing the idler to jump at random timesafer I strted using the rope the belt was on in 10 minutes.

Dryer stopped spinning, but still putting out heat

  • Customer: Janice from Winston Salem NC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Basically, I just did everything in the Parts Select video - it's what gave me the courage to attempt the repair myself and I am a 61 yr. old woman, who's not in great physical shape! The belt had broken. The two things that gave me the most trouble were disconnecting the tab on the door switch assembly and getting the screws to line up when replacing the front panel - one side lined up fine - the other needed a good push and an "alley-oop" to the side with my hip to fall into place. I did a few things that were not in the video which I think really helped me out. (1) I put an empty quart sized paint can under the dryer drum to hold it up - that really helped - I only had to support it slightly myself when threading the new belt. (2) I put a piece of duct tape across the bottom of the idler pulley to keep that from falling out of the holes when I was threading the new belt - that worked like a charm. Just be sure to remove the piece of duct tape and the paint can before you close up the dryer, if you decide to follow those two tips. (3) I also eventually put something under the front door panel to help raise it up and get it more in line with the two holes that it connects into, which made it easier for me to get it back into place. (4) Have some bandaids on hand - I sliced two fingers on different parts while installing the whole kit. (5) After you are done, either clean out the dryer vent hose or put a new one in - I was surprised by how much lint was clogged up in there. I never repaired any appliance before and if a 61 yr. old weakling like myself can do it, anyone can. Parts Select Rocks - the kit arrived a day and a half after it was shipped out and the video tells you everything you need to know to do this repair yourself and save big money. $49 versus probably $150 for a repairman and $500+ for a new dryer. Dryer is running like new! Would definitely do this again, if this or another dryer broke in the future. Thanks!

Load whinning sound

  • Customer: Gary from Pasadena TX
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I reviewed the instruction video. Excellant video. exactly like my dryer. Just followed the instructions. I did put a shoe under the drum for easier installation of belt onto idler pulley. I vacuumed and cleaned inside. Really not that dirty.Excellant web site and video instructions. Wish I had done the repair sooner. Also God Bless the residents of OK city, Moore, and ElReno.

rear seal hanging inside the dryer and lots of lint escaping

  • Customer: Jeanette from Celestine IN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
It was fairly easy, the comments and pics on this site were quite heplful. I just took out the screws on the lint trap and popped the top by pushing in on the clips with a putty knife. zlift the top and swing it back. I cut the old belt with a utility knife since i was replacing it and lifted out the drum. the drum wheels just pop off and on so they are really easy to replace. next I took off the old rear seal with a putty knife and put the new one on. This is a messy affair if you are not careful, I ended up with adhesive all over my hands. Next loop the new belt over the drum and replace it aligning it. You kneed someone to help you hold the drum level while you replace the belt wheel and front. Run the drum around with a putty knife under the new seal to make sure it is not tucked under anywhere. Put it all back together and you are done.

Dryer wold not turn off. Timer failed.

  • Customer: Jack from Oxnard CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Simple to remove the back cover, two screws holding the timer, unplug wires from old timer, install on the new one. New timer was exact match to the old one.

No heat in dryer

  • Customer: Maureen from Manalapan NJ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
We started with replacing a thermal fuse, went onto heating element & then to replacing the high limit thermostat. The replacements went very easily with your videos, but unfortunately it did not do the job & there is still no heat.

dryer just quit working during cycle and wouldn't restart

  • Customer: Greg from Winter WI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
just looked up my make and model on parts.select. looked at other peoples problems and went thru the parts list and ordered. videos on installation are helpful.
All Instructions for the 11066862500
1,771-1,785 of 1,876