11066862500 Kenmore Dryer - Instructions

I watched a video from Parts Select and learned that most problems with gas dryers revolve around two things: a broken door switch and a burnt fuse. I knew my door switch was broken. So I figured out how to lift the top of the dryer (unscrew two bolts in the back and two screws under the lint screen) and pry the hood open.) The switch was right there, held in place by two screws in the door frame. I received the part I ordered the next day, on the simple ground delivery. I replaced the door switch, closed the lid, tighten everything down. Problem solved for $15!

Remove Lint filter remove two screws that hold lint trap to top of dryer.Use putty knife to push on two top clips that hold top of dryer down on body of dryer.Lift top and locate door wire that go to switch,romove two screws that hold switch unplug three prong connector plug in new switch and reverse disassembly instructions.

I followed video instructions. Raised the top, slipped off the front, installed the belt, aligned, installed tension part, reinstalled front, lowered the top and inserted lint trap. Job done. Quick and easy. The video was the key to the whole project.

Was shipped a new heating element and I installed it. The ordered new heating element was delivered in two days! I followed the instructions that came with the element and installed it in about 8 minutes. Piece of cake!

This was my first dryer repair. The only difficulty I had was figuring out how the belt tensioner was set up with the belt. The old belt broke so I didn't know how it was suppose to work. Anyway, it took a few minute to figure out that one end of the bracket was a "spring" that allowed it to flex a long ways! Pretty easy job.

Followed the video instructions, and that was not the problem.So I ordered the next part. Then it worked.

Easy to follow videos on your site made this repair a breeze. I ended up having to replace the high temp cutoff as well but for 60 bux my dryer works like new. The repair man wanted $100 just to come look at it. Could not have done of without the easy to follow video.

ordered the part recived the parts and installed the part that easy. saved us lots of money did not have to buy a new dryer.

I thought I would do it myself and figured that because it wasn't heating I would replace all the thermostats and thermal fuse. Because I wanted to get it going right away, I also ordered a timer just incase. Turns out it was the timer and not the thermostats or fuze. I have a virtually new dryer again. Replacing the parts was really easy and didn't take long. Word of advise is to use an electrical (ohm) tester to determine which part is faulty; this will also save money by not buying not-needed parts.

Removed the back panel with a 1/4" nut driver on a Ryobi impact driver. Used multimeter to check the thermal switches and the heating element. The element was broken. Went to the PartSelect web site and quickly found the part by using the model number and verified the right part by comparing the photos to the actual part. Placed an on-line order at approximately 1:00 pm and the part arrived at 2:00 pm the next day. Cleaned out the dryer vent and it works better than it has in a long time. Great web site and delivery from PartSelect and didn't have to run around town looking for the part.

I followed instuctions, also watched a how to vidio, had a little problem reinstallig front cover. The job took a little over a hour. The squeel was coming from old style belt tensioner.

I followed exactly the video. It really was that simple. My 5 year old even helped me unscrew the nuts. The Thermostat was on the lint shaft and unscrewed easily. Once out I removed the wires. The hardest part was removing the wires, They were really tight. I replaced the wires and screwed in the part. Before I replaced the back I cleaned out the lint tube and turned on the dryer. I saw the flame and the heater kicked right on. I replaced the back and was done. *****However the next time the dryer went the heat didn't remain on and turned off too soon. I did some more research and found you usually need to replace the thermal fuse at the same time on Whirlpool units. So I have ordered the part and will let you know if kept the heater from turning off too soon.

Learned that my Kenmore dryer was actually a Whirlpool model. Removed kick plate in front of dryer. Removed the cover to the blower wheel. Cleaned out Dryer with vacuum cleaner. Used a multimeter to check for continuity on all thermostats, fuse, and heating element. Decided it was the cycling thermostat. When ahead and replaced the fuse at the same time. Checked out the installation video on this site, wwwPartselect.com ( it was very helpful in understanding how to remove the cycling thermostat - needle nose pliers helps in pulling of the connect wire clips - knuckle buster). Ordered next day delivery. The parts were on my front door early next morning FEdEX ( i live in the very corner of the NW US). Nice!

(Always unplug dryer before making any repairs) I opened the dryer and checked the heating element. Making sure that the connection was good and nothing was damaged, I determined the problem was overheated wires. They melted and lots connection. I replaced them with the heating element wire connection kit. Easy to install and simple to get right. I cleaned the dryer again with a vaccum cleaner, removing all the lint, and checked the vents, making sure they were clear...I turned the breaker on (it was tripped when the dryer overheated)and everything worked great.

The video you had of my dryer was different then my dryer and the pulley was in the middle of the bottom and the motor and fan were in front of it. I had to replace the belt without being able to see what I was doing. I couldn't get it at first then realized there was tension on the pulley wheel and had to pull it towards the other wheel in order to get the belt on there. Once I pulled the wheel it went on really easy. My first time working on a dryer but I knew I could do it myself.