11066112500 Kenmore Dryer - Instructions

Could not be any easier. For less than $20 and 15 minutes time, I couldnt be happier.
All that was needed is a nutdriver to remove a 1/2 dozen screws to take the back panel off. Then a phillips screw driver to remove the thermal fuse. Unplug 2 wires and then attach them to the new fuse. Put it all back together and done!. Working dryer.
PS: I had enough gas line and ducting connected to the dryer ,so thatt I was able to get behind it with out removing them. This may have taken another 15 min. if I needed to do this and two adjustable wrenches.

Followed the instructions on the video

Removed top of dryer and front panel per instructions and removed belt and drum. After removing what was left of the old rear drum seal I scraped off and sanded the old adhesive off. Reapplied new adhesive and installed new seal after about 3 to 5 minutes (let adhesive get tacky) I then used about a dozen spring clothes pins to hold seal in place while adhesive set up. Reinstalled drum,belt,front panel and top and job was complete. Time included letting adhesive set up. Easy and inexpensive, thank you parts select.

Very easily replaced both parts. Works perfect!!

I lifted the top of the dryer. I unhooked the hangers from the door and took it off. I pulled the drum out, took the broken belt off, slid the new one around the outside middle of the drum, turning the rib side of the belt out,and ran the belt through the pulley attached to the bottom base of the dryer (tension pulley, right hand side), slid the drum back inside the dryer frame, reattached the door, closed and snapped the dryer lid and it worked great!!

Had to order idler lever and wheel as the one in the kit would not work. Best to buy part specific for your dryer. Repair was easy, just watch repair video. Sounds like new dryer again

Your customer service was great, but your video wasn't particularly helpful because of the extreme age of my dryer. For one thing, with these really old dryers, you don't have to slide the drum out at all; you just unscrew the front panel and slip the belt in that way. The printed diagram that came with the belt helped me figure how the belt slips through the pulley assembly, but the drawing could have been more clear. In spite of my bickering, I probably saved $50 fixing it myself.

Disconnect electric power, the top & cabinet are connected by 2 reusable locks about 4 inches from each front corner, use a thin flat putty knife or similar object, push inward on a lock while lifting gently on the front of the top piece, then let the top rest against the wall. ( a wire on each end of a safety switch for the dryer door may need disconnected) Remove a screw from each front corner of the cabinet, then pull upward on the loose front panel to access the drive motor, remove old belt. install new belt by lifting the front of the drum just high enough to allow the new belt, place groves of belt against the drum and around the motor pulley and belt tensioner, re-install cabinet front, (re-connect safety switch wires) return top and push down at cabinet locks.

I watched the video on PartSelect for this model. It was very easy to follow. The thermostat was mounted on a terminal lug which needed a little prying but not bad. Saved a least $140.

I took one piece off at a Time. Made sure that each wire went to the correct place. I felt so good as a woman to be able to fix a necessity in our House without having to call a repairman to fix it for us. We are 3 women in our New Home. Im 46 My life partner is 48 and Our Daughter 17. I can't tell you how thankful i am for watching your video on how to do it. Thanks Part select. Dena , Ave & Fe .

I checked the thermal fuse for continuity and had none.ordered part arrived next day. I took a picture with phone to idenify wires. installed in a short time.dryer works like new

I'm almost 72 years young,but I replaced the heating Element and with your vedio it was so simple.I did it with no problem.Thank You and I'm proud of myself too.I saved a lot of money.Evelyn

Before calling a repairman, I researched the problem at partselect.com. I am so glad that I did. It saved be a lot of money. I was able to narrow down the cause of "No Heat", and ordered a new Heating Element for the dryer thru partselect.com. The part arrived very quickly, and I was able to install the new part by first watching the installation videos at partselect.com. This could not have gone smoother, and I could not be happier. And, "no", I do not work for partselect.com. :)

repair went just as describe in video.

I watched the videos associated with the parts. They were easy to understand and I could follow the steps without difficulty. I replaced both the cycling thermostat and thermal fuse. Separately, I also replaced the "push-to-start" switch. Dryer would still not start. I called the repairman. Problem turned out to be a loose wire that had shorted out in the electrical bar near the "push-to-start" switch. All parts I replaced are determined to be good and will be tried next time I experience the dryer "not starting".