11066002010 Kenmore Dryer - Instructions

I removed the top of the dryer and removed the faulty switch form it's mating connector. The simply removed two Phillips Head round headed screws with a screw driver and replaced the part all within 15 minutes. However, I also heard that it wasn't drying properly so after making sure my dryer vent was free of any lint build up, I removed the back of the dryer. Once removed, I completely cleand any dust from inside the dryer, then checked all of the visable wire connections and then went to PartSelect's fantastic web-site. Her they catagorize the top 7 reasons that could cause the problem (in my case) not drying and thenproceed to give you an idea of the most likely cause by publishing the failure rat in per centage values in decending order, they also provide schematics and the on top of all of that...they provide mini-videos not only showing you wher the parts are located but the step by step instructions on how to remove them and replace them. After all of this, I took my ohm meter and actually removed all of the 7 parts suggested, cleaned them up, ran a continuity check on each part and found them all in working order. Replaced the parts and checked the heat and it was back to normal!! There must have be a lose connection causing the problem. But, I can guarantee that the next time I have an appliance problem...I'll again be calling on PartSelect.com. They are awesom and they will be highly recommended to anyone I know that is experiencing problems. I have not ever seen a web-site that was so complete in excellent service. And there prices and shipping time speaks for itself. They are great!!

Called a appliance place. They said it was a serious problem with master board and it was gonna cost 425.00 dollars. NO THANKS. Ten minutes to open ten minutes to find the problem. ( which was no were near the master board). Seconds to find and order the parts on partselect.com. got it next day. 15 to 30 minutes later my dryers running like it was brand new! Love it.

Unscrewed bolts off back (2). Took dryer vent out unscrewed the bolts (2) pushed top back and lifted up. Open door unscrewed the bolts (2) to the safety switch pulled the connection (wires) apart and replaced with new safety switch.

Queried the Internet for my model number of dryer. Found Part Select web site. Went to the site and entered my model number again. Found a list of common problems and my particular dryer problem was listed. Only two possibilities - thermal fuse or timer. Studied the diagnostic criteria for thermal fuse and that seemed to fit my situation. Watched the video of how to replace the thermal fuse. After watching the video, I was convinced I could fix the dryer. Ordered the thermal fuse and it arrived in about 2 days. Followed the instructions previously viewed on the video and replaced the thermal fuse. Success!! Mission accomplished!! I felt great that I had done this by myself with help from Part Select. A service call from a repair establishment would have cost about $130.00. I fixed my dryer for about $9.00 plus shipping cost of about $7.00. And I didn't have to wait for two weeks for a repairman to show up and occupy my whole day. I forwarded the Part Select link to all of my friends and relatives and told them to use Part Select for their repair needs. Awesome web page and service! Use them!

It was simply a replacement filter. No work just replace in slot. Thanks for great service and for sending in one day! We were shocked that the part arrived in one day! Will use your service again!

I first pulled the drum and turned on the dryer. The igniter never turned on. So I unplugged the dryer from the outlet and measured the resistance of the igniter, which was ok. I pulled the back panel and checked the thermal fuse, which was open. I also pulled the lint system plenum off of the unit, which was clogged with lint. This probably caused the thermal fuse to overheat. I cleaned out the lint collection system, replaced the thermal fuse and re-installed the drum. dryer is now working fine.

removed bottom panel & removed old element.

As per video instruction that came with the email order conf

flipped THE BREAKER (very important!). Removed the cover on the bottom of the dryer (2 screws), made easier because dryer is stacked on top of washer. Removed the heater box (3 screws). Thermistor located on top of the blower housing (right side). removed old thermistor (2 screws) and unplugged the wires. Plugged the wires into new thermistor, installed the thermistor, replaced the heater box, then tested the dryer. It seemed to work fine. Replaced the cover. It has worked fine ever since.

Removed the front lower skirt with two 1/4"hex screws. Vaccumed all inner parts exposed. Removed three 1/4" screws holding the blower housing.Memoved the bias thermister again two 1/4" screws. Make sure all inner exaust pipes and rear chimney gas or electric are clean and lint free. Re assemble and test the unit. Install the skirt and make sure the dryer is level Jack, Pa.

Followed instuctions on video accept our appliance was the Duet HT model so we had a glass window to deal with. Just a few more screws to keep track of but otherwise a very easy repair.

found that the lever on the switch was broken,i found one on the part select website and ordered it. the picture was very helpful in confirming the right switch was being ordered.thank you

ordered new latch. Arrived promptly. Installed in 5 minutes. Actually easied than the video. Thanks

The Door Catch Kit had clear instructions for installation and included multiple replacement catches to fit several different sizes/varieties of dryers. I used a screwdriver to pry out the broken door catch, popped in the replacement, and was done! As usual, PartSelect had what I needed at a good price, with clear instructions for any needed installation. Fast shipping, too.

Disconnected power to the dryer, opened the top of the dryer by sliding a thin scraper underneath the top on the front of the dryer and the pushed the top of the dryer up. I then disconnected the wire on the switch to isolate the switch from the wire in the dryer. I then removed the switch by unscrewing the two screws on the switch and then replaced it with the new switch. I then reconnected the wire to the wire in the dryer.