1106517741 Kenmore Dryer - Instructions

Got the latch kit, found the correct one, popped it in...dryer works! Thanks....

follow the vidio. removed lint screen. removed screws securning the lint trap guide. used to disconect the two clips honding the top cover and lifted it up and secured it as not to drop down. removed two screws at top of front paned and removed it. took out drumb. took off the two rollers and remounted the drumb and belt. replaced front panel and two screws. lowered top panell and two screws. replaced lint trap. turned on to see is noise stoped and it had. done

Having read the instructions and watched the tape, I pried out the remaining catch with a flat screwdriver, read about what the color scheme on the parts wasbout and pushed in the correct part. Voila ! Done in probably two minutes.(By an 82 year old woman!)

changed fuse,radiant flame sensor. no help. bought a new dryer. i don't think the gas valuve was opening.everything seemed to be working properly,just no gas.

Got online with parts select, easily found the parts needed and ordered them. They arrived very quickly. The repair itself took all of 5 minutes and now the dryer door stays shut like it is supposed to. Only complaint is shipping was more than the parts but then again, I didn't waste a lot of time running all over town looking for what I needed. So, in the long run I saved money , especially when compared to a calling someone else to fix it.(big bucks for even the most minor service call as you all know).

pop off put in done

following the repair video made it super easy. thanks!

Followed troubleshooting steps. Checked thermal fuse (shorted)- OK. Checked igniter (about 70 ohms) - OK. checked flame sensor - (open) BAD (should read shorted). This part is normally shorted then opens when the igniter gets hot causing it to open and thus turns on the gas flow. An open flame sensor does not permit the igniter to turn on.

Replaced actuator switch lever. Exact replacement. Worked like a charm.

I consulted the internet and found Part Select and use online repairman to diagnose the problem and found the roller solution with the parts, video and parts illustration. Sure enough, the left roller hole was worn and egg shaped. I ordered the parts on a Wednesday afternoon. While I waited, I got all the lint from the bottom pan, motor, and around the burner cleaned out and ready for the new parts. The parts arrived Friday morning and I installed them and put the dryer back together before noon. The dryer works and sounds like a new machine. Now I am ready to attack the squeaky fan motor in the freezer compartment of our refrig.

Located broken front door safety switch actuator. Ordered new part shown on the diagram. Removed broken part, installed new part, start dryer,runs fine.

Order one new latch, receive 2 spares. Pushed new latch in, re oriented the catch. was done in less than 5 min

By following the repair video available, I took off the top and front panel of my dryer, removed the drum, removed the old drum support rollers, vacuumed out the inside of the dryer (so much lint!), replaced the drum support rollers, and put the dryer back together. Dryer runs like brand new and is very quiet. Repair was extremely easy to do. Got the replacement parts in about 2 business days. PartSelect repair videos make the repair easy too! Lots of satisfaction for a girl to repair her own dryer!

We found great video instructions via youtube.com to give us an idea to what might be the problem even before we opened the dryer. Then we opened the dryer top and front door and then removed the belt and drum. We then saw that one of the drum wheels was worn and the rubber part of the wheel was warped off. Once we saw what part we needed we ordered them through PartSelect.com since their wonderful instructions helped us out. Once we received the part we easily removed the old drum wheels and installed the new ones...super easy! Then we had to put the drum back in with the belt. The only "difficult" part was looping the belt around the motor because there was a lot of tension. Once that was set we just put the door back on and then the top! I guess the only snags we had during the process was where exactly to remove screws or pry open certain places b/c every dryer is a little different. I just advice people to really look at their dryer and think about how it is held together instead of just unscrewing everything. We are so glad we found the partselect.com instructions via YouTube.com. We were ready to buy a new dryer but fixing the dryer ended up only costing us $30! Our dryer is so quiet now, just like it is brand new.

I watched the repair video on your website,that was abig help , dryer runs good