11065064500 Kenmore Dryer - Instructions

removed back cover and with unit unplugged, removed one wire from each device (thermal fuses and switches) and measured with multimeter. Found thermal fuse open. Removed and looked up and ordered part. Installed fuse and buttoned er up and all good. Hardest part was putting the exhaust hose back on the floor outlet!

I followed the video for this part. Opened the front panel. Unscrewed the brace on the bottom. Turned the element housing and pulled out after disconnecting the wire leads. Unscrewed the original parts. Screwed in the new parts. Reversed the sequence and ran a load of towels. It was easy and fixed the problem.

I studied the instruction on the partselect.com site, followed the directions to discover the problem, ordered the part from them, installed it as in instructed in their video, and it has worked perfectly for the past 5 days after doing a mountain of laundry. I took the opportunity to clean my dryer interior from all lint and dust as well as the vent. I suspect lint is what caused the problem after I washed some new flannel sheets which clogged my vent cover outside. I cannot say enough good things about the partselect videos. I'm ready to tackle a few other appliances. One note about the Kenmore Elite Dryer 110 model: Do not take the back off. I removed the screws which caused the steel plate to drop a little at the back of the dryer. Then I could not put the screws back in. To fix this, I removed the screws from the control panel and pushed it forward to reach just inside the top back of the dryer...pulled up the steel plate and got the screws to line up and put it all back together. The only other tricky part was getting the heater unit back in to the slot at the back of the dryer. I finally used a little brute force to push it in far enough, then turned it a quarter clockwise to the correct position. My husband was impressed that I tackled this project by myself. Hunting season was on in MN. THANK YOU PartSelect.

Took off front bottom panel reached in removed part that was very dusty. Put in new part. Cleaned out lint inside dryer. Works like a charm.

Removed back and found fuse bad, repalced fule.

At first I thought it was the ignitor, so I replaced it. No luck there. Next I went to the Part Select web site...that showed that the Thermal Fuse was the cause of this symptom 45% of the time. I installed the fuse and now my dryer is working!

open dyer door replace lint filter perfect fit, good price, fast delvery. thank you

downloaded video

removed cover panel an unbolted and replaced and it works watch the video best 100 dollars we ever spent

Removed the old fuse and replaced with the new fuse. Of course, I had to remove the back of the dryer but very easy and the cost was less than $20.00. Definitely worth it because we did not have the money for a new dryer. PartSelect.com is awesome!

First I replaced the heating element. That did not fix the problem, so I used an ohm meter to test the thermostat and fuse (thermal cut-off). One of those was bad, so I ordered the thermostat/fuse conbo and put those in. The hardest part was getting the wires to the right places. I labeled them with masking tape and a sharpie, but maybe they are sized so they only fit one place. I didn't check. The actual work of changing out the parts was super easy. I recommend testing those three parts-heating element, thermostat, fuse-with an ohm meter before buying something you don't need. I now have a spare heating element and thermostat. I should be good for another ten years!

First of all, your operator was patient and courtious and extremely knowlegable. They knew right away what part was required. I watched a video on youtube describing the job. When the part arrived, on time, I just did what the video told me to do and in under 30 minutes the jobwas done and the dryer works perfectly. I'll be back for sure

Remove wire terminals, & four screws, install new parts. Very simple fix! This is the second time I've used Parts Select to fix my appliances. Very satisfied customer!

When the part came in my husband was not home and I figured I could put this part on myself. I took the part downstairs, used the nut driver to remove one screw, took the two wires off the old therma fuse, put the wires on the new therma fuse, and screwed the new therma fuse onto the back of the dryer. It really couldn't have been any easier.

took of the back , took out the drying coil ,put the other in , but back on . now it works saved alot of money. love it. Thank you parts select.