11064912200 Kenmore Dryer - Instructions

I followed most of the directions as explained in the online video and what came with the parts. Had to give the glue a little extra time to dry than the directions specified, but that was probably because of the amount of glue I put on the rear seal.

unplug unit ,remove back cover six screws, slide off two wires on thermal fuse, remove one screw remove and replace fuse, reattach wires replace back cover

We followed the instructions on the video step by step. The repairs was very easy. I'm glad I did not pay the repair person 4x the amount I spent on just parts and delivery. DIY was the best option especially compared to how much money we saved.

Our make/model was not on the online instruction, but it was similar. Ours had a glass (plastic)front window in the door. To remove the top catch you had to take out the top four screws that hold the door together (philips head screws) allowing you to pull back the gray plastic strip to access the top latch, then replace it like in the online directions using a needle nose pliers. The bottom catch, once the two remaining the screws were out gives you access to the bottom catch. Remove it with the pliers and snap the new ones into place. You can completely take out the window when you replace the bottom latch if you want.

My dryer all of a sudden stopped tumbling. When I opened up the machine, it turns out that the drive belt was broken. I simply put in the model number in PartSelect.com and found this kit that came with the belt, and drum rollers. The belt fixed the tumbling issue, and after replacing the rollers, the machine is as quite as a mouse! The instructional video helped show me exactly what to do and expect. This was my first time fixing an appliance, and it only took me 45 minutes!

Just pulled the old parts out on door latch and put the new ones in. Thanks Parts Select for your prompt response and easy process for order and shipment.

I had my laptop next to me and paused the tutorial video
as I did each step to chnage the drum rollers, idler pully and belt. Dryer runs great with no more screeching!

The video from your website is exactly the steps I followed to remove the old door switch 3 wire and install the new one. Very easy! NOTE: 1 Week before the dryer totally stopped working, my mother opened the dryer door when it finished (sound alert) but, the dryer was still spinning + the light did not come on. I noticed that the small black lever (part of the door switch wire which sticks out & presses against the door when the door is closed) was extremely loose. It seemed as if the lever was broken (perhaps the last time I used the dryer the door slipped from my hand and broke the black piece). Video tutorial was great!

I watched a video from Parts Select and learned that most problems with gas dryers revolve around two things: a broken door switch and a burnt fuse. I knew my door switch was broken. So I figured out how to lift the top of the dryer (unscrew two bolts in the back and two screws under the lint screen) and pry the hood open.) The switch was right there, held in place by two screws in the door frame. I received the part I ordered the next day, on the simple ground delivery. I replaced the door switch, closed the lid, tighten everything down. Problem solved for $15!

Remove Lint filter remove two screws that hold lint trap to top of dryer.Use putty knife to push on two top clips that hold top of dryer down on body of dryer.Lift top and locate door wire that go to switch,romove two screws that hold switch unplug three prong connector plug in new switch and reverse disassembly instructions.

I followed video instructions. Raised the top, slipped off the front, installed the belt, aligned, installed tension part, reinstalled front, lowered the top and inserted lint trap. Job done. Quick and easy. The video was the key to the whole project.

Was shipped a new heating element and I installed it. The ordered new heating element was delivered in two days! I followed the instructions that came with the element and installed it in about 8 minutes. Piece of cake!

This was my first dryer repair. The only difficulty I had was figuring out how the belt tensioner was set up with the belt. The old belt broke so I didn't know how it was suppose to work. Anyway, it took a few minute to figure out that one end of the bracket was a "spring" that allowed it to flex a long ways! Pretty easy job.

Followed the video instructions, and that was not the problem.So I ordered the next part. Then it worked.

Easy to follow videos on your site made this repair a breeze. I ended up having to replace the high temp cutoff as well but for 60 bux my dryer works like new. The repair man wanted $100 just to come look at it. Could not have done of without the easy to follow video.