Models > 11064672400 > Instructions

11064672400 Kenmore Dryer - Instructions

All installation instructions for 11064672400 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11064672400
1,771-1,785 of 1,873
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

dryer tub drive belt broke

  • Customer: Ray from Salisbury NC
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unplugged the power cord. Removed two screws on lint vent , used putty knife to release clips to raise top at front of unit. Disconnected the plug from front door switch. Laid dryer on its back. Removed two screws to remove front including the door. Vacuumed lint from inside unit. Installed belt temporarily using two pieces of masking tape to hold it in place while properly routing the belt. Gave the tub a full turn to insure alignment.. Reinstalled the front of unit with the two screws. Righted the unit and snapped down the top. Replaced the two lint vent screws. Plugged it back in and done! Piece of cake!

The dryer had no heat but would tumble

  • Customer: Russell from Natick MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I Removed the rear panel. Then I used the instructions online to locate and test various parts and determined what was defective. I order the parts online and received them the next day. It took less than 30 minutes to do the repairs. The dryer works great.I will be using partselect.com in the future and would recommend them to anyone who is having problems with their appliance.

Clothes getting hot, but not getting dry

  • Customer: barry from roswell GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Verified that the heater element was working; drum and contents were getting hot. Could hear the thermostat clicking on/off as the element started to glow. Drum stayed very steamy the entire time; consistent with no airflow. Fan motor was running, dryer vent/line were clear. Verified cold (not hot) air from the external vent. Seals had degraded to the point that the fan was not drawing air from the drum, but from inside the dryer cabinet at the lower seal (by the fan blades); hot air was escaping from the upper seal and was causing the dryer cabinet to get unusually hot. Installed these 2 seals, and the dryer is working perfectly now.

Complete disassembly and diagnosis

  • Customer: jeff from bridgewater NJ
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I am more fortunate than most because I have extensive mechanical repair experience and my father has extensive electrical repair experience...he read the schematic while I placed the probes in the appropriate locations...I completely disassembled, cleaned, replaced all maintenance parts (felt gaskets [front & back of drum], drive belt, foam gaskets on heat exhaust duct)...the culprit was found to be the Thermal Fuse but I also replaced the Cycling Thermstat just because I serviced the entire heat exhaust duct (it had a fair amount of lint in it after 14 years...all other sensors on the heater unit and switches (door switch & centrifical switch (you will never find this unless you take out the drive motor [it is inside the drive motor] were tested and found to be good...all dash controls / switches were found to be in good order also...Part Select is wonderful to work with...they said allow 5 days but the parts were here in 2...! Just a little help for all of you out there...putting the felt gasket on the back of the drum will test your patience...it is a little smaller than the drum and as you get near the end with the glue it is extremely difficult to get on...I would recommend having a lot of clamps handy to hold the portion that is already glued to drum in place and another set of hands to rotate drum while you are stretching on the remaining foot...! One other thing...if you don't want to go thru everything I did chances are quite strong that if the dryer does not restart (after first failing) I would say to just order the Thermal Fuse for the 9-10.00...it is a pretty safe bet this will be your problem...I believe the dryer will start / restart even if the heater unit is no good and or the Cycling Thermostat goes bad since that just senses humidity...? The switch and fuse on the motor are not replaceable here...my father had contacts to get those parts from the motor company but...one is designed to stop the motor if it becomes hot which in all honesty I think would be pretty rare...it is in an open area...the other switch inside the motor prevents the heater from heating up until the motor is spinning which inturn spins the exhaust fan which is a safety feature but again I think motor failure is pretty rare.

Dryer made all kinds of noise

  • Customer: Melissa from early IA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
So glad we tried the belt and rollers before going out and buying a new one. Very quiet now,so happy!

drum wheel had flat spot

  • Customer: Michael from Jupiter FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
Replaced both drum wheels and belt and cleaned lint out of entire unit. Works perfect again. Great fast parts with super on line instruction if you need it.

Thumping noise

  • Customer: Susan from San Mateo CA
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed general instructions from your you-tube video. It was much easier than expected. We didn't know if it was belt or rollers, turned out to be roller, but since we bought both we replaced both.

loud noise

  • Customer: Cindra from Winnemucca NV
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
I watched your repair video and followed what the repair man said and did, it was a snap! I needed my dryer fast so decided to do it myself. I am a 65 year old female and petite, so I say if I can do it anyone can. Your video was the key to my sucess.

right side drum roller rubber came off,this caused drum to drop and belt tensioner to release.

  • Customer: John from New Bern NC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
removed two screws from filter chute,raised top of dryer and removed front panel,lifted drum out,replace both rollers,replaced drum,reset belt tensioner replace front panel,lowered top,put screws back into filter chute.

Banging and screeching noise when dryer was turned on.

  • Customer: Sarah from South Hero VT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
We found great video instructions via youtube.com to give us an idea to what might be the problem even before we opened the dryer. Then we opened the dryer top and front door and then removed the belt and drum. We then saw that one of the drum wheels was worn and the rubber part of the wheel was warped off. Once we saw what part we needed we ordered them through PartSelect.com since their wonderful instructions helped us out. Once we received the part we easily removed the old drum wheels and installed the new ones...super easy! Then we had to put the drum back in with the belt. The only "difficult" part was looping the belt around the motor because there was a lot of tension. Once that was set we just put the door back on and then the top! I guess the only snags we had during the process was where exactly to remove screws or pry open certain places b/c every dryer is a little different. I just advice people to really look at their dryer and think about how it is held together instead of just unscrewing everything. We are so glad we found the partselect.com instructions via YouTube.com. We were ready to buy a new dryer but fixing the dryer ended up only costing us $30! Our dryer is so quiet now, just like it is brand new.

Dryer made loud noise, shook across the floor

  • Customer: Miranda from Scottsville VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
By following the repair video available, I took off the top and front panel of my dryer, removed the drum, removed the old drum support rollers, vacuumed out the inside of the dryer (so much lint!), replaced the drum support rollers, and put the dryer back together. Dryer runs like brand new and is very quiet. Repair was extremely easy to do. Got the replacement parts in about 2 business days. PartSelect repair videos make the repair easy too! Lots of satisfaction for a girl to repair her own dryer!

noise while drum rotating

  • Customer: vince from virginia NE
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
follow the vidio. removed lint screen. removed screws securning the lint trap guide. used to disconect the two clips honding the top cover and lifted it up and secured it as not to drop down. removed two screws at top of front paned and removed it. took out drumb. took off the two rollers and remounted the drumb and belt. replaced front panel and two screws. lowered top panell and two screws. replaced lint trap. turned on to see is noise stoped and it had. done

Banging noise from dryer

  • Customer: Allen from Simpsonville KY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I don't have specifics although they were emailed with my order confirmation and were perfect. I have dealt with PartsDirect multiple times over the years and have always been more than satisfied with their speed of shipment, quality of parts, and stellar instructions(even video most times). With PartsDirect, you never have to buy another appliance.

Roller hub ID severely worn.

  • Customer: Walter from Moncks Corner SC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed top and front of dryer. Removed drum. Removed old rollers from spindles. Installed new rollers and new retainer triangles. Replaced drum. Re-installed front and top.

Lots of noise, then locked up. Drum support bearings failed, locked up, twisted sideways.

  • Customer: Josh from interlachen FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
I made it very difficult. I didn't research the repair. My back is old. It's easier if you just You Tube a video. The top roller you have to take drum completely out. The bottom one, The one that failed for me, you can actually do it without taking anything apart. Access it at bottom back, two holes. I do not have small hands, it would have been easier. Channel Locks inside, 9/16th socket outside. That will loosen main axle. Then use short screwdriver or socket driver on small bracket connected to bottom of unit. Mine had one screw holding it in. Easy bottom fix. I don't really recommend replacing top till it needs it. You can only buy them by the pair too. You will be ready when time comes. I found top roller didn't actually need replacing, did it cause I had it all apart. Don't fix if not broke, right? Trust, BUT, Verify. Smaller hands, would have helped me. All I got.
All Instructions for the 11064672400
1,771-1,785 of 1,873