11063046100 Kenmore Dryer - Instructions

diagnosed problem with ohm meter. replaced thermal cutoff and hitemp thermostat

Exactlyt how your video showed me. I was a bit skeptical, but it was the easiest repair ever.Thank you

Using some advice here on this website, and a youtube video found by searching for 'idler pulley replacement' I was able to fix my dryer! Taking off the screws was simple, I used a cordless drill. I have some trouble removing the kick panel, and bent the latches, so there is a small gap between the dryer door panel and the kick panel, but it still works fine. Of note, you DO NOT need to remove the back panel, something I did and cost me some time. I am a bigger guy, so maneuvering on the floor to rig the dryer belt around the new idler pulley "in the dark" was cumbersome, but doable. All in all, an easy enough project for under $30 and less than an hour of my time. Kudos to this website, first, for the super fast shipping, and secondly, the reviewers who posted some instruction. Great job!

Using Partselect to troubleshoot, I determined the heating element was shot. Upon receiving the part, I disassembled the unit, inserted the new element and reconnected everything. It couldn't have been simpler and saved me a ton of money.

Disconnect the dryer from the power source and vent hose. Using the nut driver, remove all hex screws and the electric access panel from back of dryer. Loosen the electrical service cable clamp screws with philips screw driver and disconnect the ground wire. Remove the top panel from the dryer cabinet and the screws that hold the electrical bus in place, then remove the back panel from the dryer. Feed the electrical cable through the cable clamp and rest the back of the dryer against the side. Remove the tri-ring and old idler pulley, then clean and lubricate (WD40) the axel, and install the new pulley and tri-ring. Replace the back panel and all screws.

Lifted front top upward, removed two small/long screws holding switch assy. removed two wires, replaced wires on new switch at the N.O and COM tabs, reinstalled switch assy, lowered top down. DU FINI

Remove dryer back panel Used multimeter to find problem. Two screws held the thermostat.

Dryer was making intermittent squealing noises sometimes it was amazingly loud, sometimes not so bad. Still, I figured this couldn't be good so I wanted to find a fix. Read the stories here and everything pointed to the 'idler pulley', so I figured I'd give it a try. For me, access was the hardest part -- my laundry room is small and I can't easily get the dryer out or move it around. Not a problem with the part, just my own setup. Important to note that this repair is best done through the BACK of the unit, not the front. Once I got access to the back (removing AC and Water used for the 'steam dry feature') I also had to disconnect several of the electrical connectors to get the unit fully apart. Good news -- the actual replacement of the pulley took about 1 minute! It was just all of the moving and disassembly that took so long. The original idler pulley had worked its way off of the shaft and was out of place and causing the squealing. All is well now, and I saved a bunch by doing it myself. No more squealing!

Searched for answers on what to do when my dryer wouldn't heat and came across PartSelect videos on how to troubleshoot and repair. So I followed the detailed videos step for step and turned out to be a very simple task to identify that the thermal cut off had blown. I ordered the kit and very fast delivery had the parts in my hand in two days. Following the repair video, and a double check of the wiring diagram, had me up and running again for less than $40. I don't see a need for going anywhere else for appliance parts in my future.

First tried repairing the old idler by cleaning and lubricating the shaft. That lasted for about a week but the squealing returned. Ordered the part and had it in a few days. Replaced the idler wheel and it's been quietly running like new for several weeks now. Now wife thinks I'm Superman.

Removed the broken actuator and replaced with the new one. The time to replace the dryer door switch actuator took about 5 minutes.By the way, I purchased the dryer in 1965 and it works as if it was brand new. Thank you Kenmore for a lifetime dryer.

Removed the front cover of the dryer as well as the lint holder and framework to gain access to the thermal fuse which is behind it and mounted on the discharge side of lint fan. replaced fuse but the dryer still wouldn't heat each time the ignitor glowed. Also then replaced the solenoid (both of them) and this fixd the problem as it has been good for a week now. The solenoid issue is not easy to conclusively identify as an issue as it is inconsistent in operation.

Replaced Lint Screen

two screws on filter housing and then lift dryer to up like the hood of a car the two screws on actuator, be careful not to drop actuator, if you do use a magnet to retrieve, two screws back in then wire clip top of dryer down and two screws back into filter housing and your ready to dry clothes, not recommended but if you have to dry clothes while waiting for part a clamp on the switch will allow you to use dryer, but be extremely careful because dryer will not turn off when door is opened

Took screwdriver popped out old latch in cabnet. Took pliers popped out latch out of door. Snaped new latch parts back in.