Models > 11062922100 > Instructions

11062922100 Kenmore Dryer - Instructions

All Instructions for the 11062922100
451 - 465 of 572
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
No heat
Remove dryer back panel Used multimeter to find problem. Two screws held the thermostat.
Parts Used:
High Limit Thermostat
  • Brad from Wimberley, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Replace. Motor
Getting the fan off proved to be quite an issue. on my model, it loosened in the clockwise direction. I ended up having to completely pull the motor and clamp the unit in a vice before I was finally able to gett itloose.. Hopefully yours will not be such a problem....
Parts Used:
Drive Motor with Threaded Shaft - 120V 60Hz
  • Jon from Markham, VA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Was this instruction helpful to you?
Thank you for voting!
Dryer was not heating.
I replaced the Cycling thermostat. At first I thought I may have blamed the wrong part because the ohm meter read almost the same for the old and the new part. It took less than a day for the part to come probably because it came from Jacksonville. I haven't guessed how much I saved by not calling a appliance repair.
Parts Used:
Dryer Cycling Thermostat
  • Leland from Palm Bay, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Dryer door would not stay shut
Got the latch kit, found the correct one, popped it in...dryer works! Thanks....
Parts Used:
Door Catch Kit
  • Jerry from Yankton, SD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Needed to vent the dryer to the left side
The kit turned out to be missing a 7.40" 4" diameter vent that was needed so ending having to get my plumber to use what was there with a "cut and paste" job - took him over an hour. He did say that had the right piece been there, it would have been easy.
Parts Used:
Side and Bottom Vent Kit
  • Carolyn from Sonora, CA
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    30 - 60 mins
Was this instruction helpful to you?
Thank you for voting!
Belt Pulley
The repair went great . Thanks for the part ,will be purchasing parts from you now on.
Parts Used:
Idler Pulley
  • Katherine from Bay Minette, AL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
door would no longer catch when shut
Having read the instructions and watched the tape, I pried out the remaining catch with a flat screwdriver, read about what the color scheme on the parts wasbout and pushed in the correct part. Voila ! Done in probably two minutes.(By an 82 year old woman!)
Parts Used:
Door Catch Kit
  • Leah from Philadelphia, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
No heat, everything else worked
Pretty straight forward, only hard part was getting the housing for the heating element out. After that it was plug and play. Added benefit was cleaning out the inside and dryer vent while I was in there.
Parts Used:
Dryer Heating Element
  • ERIC from DAYTON, OH
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
The seal on the lint filter was not well attached
Replacing the filter was easy - the new filtes's seal seems much more secure. The new one works much better than the old one.
Parts Used:
Lint Filter
  • Kathleen from Dyke, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
door would open during drying cycle and shut off machine
Got online with parts select, easily found the parts needed and ordered them. They arrived very quickly. The repair itself took all of 5 minutes and now the dryer door stays shut like it is supposed to. Only complaint is shipping was more than the parts but then again, I didn't waste a lot of time running all over town looking for what I needed. So, in the long run I saved money , especially when compared to a calling someone else to fix it.(big bucks for even the most minor service call as you all know).
Parts Used:
Door Catch Kit
  • Robert from Rochester, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Sqeaky Dryer
My husband changed the idler pulley. It took him 5 min. Thank you sooooooooooo much. Saved us 1000.00 dollars. He wanted to by a new one but investigated the problem on line. He is a handyman and was just being lazy. I ordered the part and he fixed it. I love saving money!!!!!!!!!!!!! And I love my husband!!!!!!!!!!!!!!
Parts Used:
Idler Pulley
  • Mona from Vacaville, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
door kept pooping open, clothes took forever to dry. Lot of wasted time and energy and money. Wish we would have reapired a long time ago.
pop off put in done
Parts Used:
Door Catch Kit
  • William from Murrieta, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
Was this instruction helpful to you?
Thank you for voting!
Dryer had no heat
Opened up unit and followed tech directions on inside pocket to isolate the problem to the heating element. Pulled it out and sure enough it was broken in one place. Found the part on PartSelect and ordered it on Saturday, received it on Wednesday. Replaced the new heating element into the assembly, reinstalled the assembly and connected the wires. Works like new now!
Parts Used:
Dryer Heating Element
  • Danny from Woodbridge, VA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Socket set, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
Felt around the Lint Filter was loose and would not stay
Took out the old one and put in the new one.
Parts Used:
Lint Filter
  • Janice from Central Lake, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
dryer door kept popping open
following the repair video made it super easy. thanks!
Parts Used:
Door Catch Kit
  • vangelis from rosemead, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 11062922100
451 - 465 of 572
Back to Top