11062812100 Kenmore Dryer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
dryer runs no heat and not cycling
Ordered your fuse & thermostat. Total $37.29, installed parts & still no heat. Ordered your 240v Heating element.. Total $77.43, installed part & still no heat, Removed 30amp circuit breaker and purchased replacement for $11.30 in town. Installed breaker, dryer now has heat. Still smiling as I keep telling my self I performed preventive maintenance on my dryer!!!
Parts Used:
-
Donald from East Butler, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
tumbler would not turn
I followed the video directions exactly as instructed and I had no problem doing the repair myself. And if I can do it being a woman with no help you can do it. Easy peasy~
Parts Used:
-
LORRIE from ARNOLD, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
dryer would not start and light was not working
unpluged dryer from wall,lifted top of dryer unpluged door switch took out two screws that hold switch, installeed new switch, put top of dryer down, plugged dryer back into wall, very easy repair.
Parts Used:
-
Randall from Schertz, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
wont shut off &no light
-
RUSSELL from POUGHKEEPSIE, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Dryer not hot enough
1.Installed thermal fuse. I thought this was the problem as a few years ago this fixed the dryer that was now experiencing a similar problem. Problem persisted. 2. Installed new thermostat. Problem persisted. 3. Installed new igniter coils. Eureka! Problem solved!
Parts Used:
-
Steve from Buffalo Grove, IL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
timer not working. No heat
I simply pulled the dryer away from wall. Cleaned vents. Pulled plug out from outlet. Unscrewed the back panel and removed the cycling thermostat and fuse as per your instructions. Since I had the back panel removed I cleaned the inside of lint as well. Put the back panel back started the dryer and everything was perfect. Saved myself at least 150.00.
Parts Used:
-
Mark from Staten island, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Gas dryer was not heating.
I ordered the part I suspected....which was indicated by approximately 44% of the users having success replacing the thermal fuse. After watching the video on how to perform the repair, it was a snap! Removed the 9 screws, removed the vent hose, popped out the fuse, and replaced it. After checking to see if that was the problem....which it was, I reassembled the dryer. It only took more time because I chose to vacuum any exposed areas. THANK YOU!
Parts Used:
-
john from mohnton, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Clothes getting hot, but not getting dry
Verified that the heater element was working; drum and contents were getting hot. Could hear the thermostat clicking on/off as the element started to glow. Drum stayed very steamy the entire time; consistent with no airflow. Fan motor was running, dryer vent/line were clear. Verified cold (not hot) air from the external vent. Seals had degraded to the point that the fan was not drawing air from the drum, but from inside the dryer cabinet at the lower seal (by the fan blades); hot air was escaping from the upper seal and was causing the dryer cabinet to get unusually hot. Installed these 2 seals, and the dryer is working perfectly now.
Parts Used:
-
barry from roswell, GA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Broken Belt Tub wouldn't turn
TURN OFF POWER TO DRYER............................. Pay attention to where everything is as you take it apart, so it can be put back the same way. Take out the two screws by the lint screen. Use flat tip screwdriver between space in front of top to help lift top. Use rag on tip of screwdriver so as not to scratch it. Take out two screws inside the front panel at the top. One on each side. Unhook the switch wiring. Lift up the front panel to take off. The tub will be loose, so it can be taken out to inspect other components. Some call the tub a drum. Be sure to see how the belt tensioner is attached, so it can be put back on the same way, if it comes loose. It is under the tub. Take out old belt. Put new belt around tub. Make sure the tub sets on the two rollers in the back of dryer. While holding tub, put the belt around the grooved pulley on the motor. Grooves are face down against the tub. Feed belt through the tensioner. Put the bottom of front in on the tabs. Be sure belt is still in place around pulley and tensioner etc. Hold tub through front door and close front. Put the two screws back in on each side. Close top and put the two screws in at the lint screen. Done. Turn power back on. Turn on dryer to see if it operates properly. If not, check out your repair to see if everything is connected properly.
Parts Used:
-
Leslie from augusta, WV
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
No Heat
-
Juanita from Plano, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Dryer was not heating on any setting.
Removed rear panel and visually observed coil on heating element was broken. Ordered element and replaced. Works great!
Parts Used:
-
Russell from colgate, WI
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Socket set
Was this instruction helpful to you?
Thank you for voting!
dryer door switch was broken
-
Arthur H from Boca Raton, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
no heat
unplug take off vent hose and back panel unscrew one bolt holding the fuse disconnect 2 wires. Connect the 2 wires to the new fuse hold in place with the bolt put back on the back panel and vent hose plug in and your done
Parts Used:
-
Juanita from Plano, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Broken belt
Used PartSelect instructions for routing belt & a customer's valuable guidance.
Parts Used:
-
Christopher from Skillman, NJ
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
heating element replacement
Remove rear panel, unplug element & replaced with new .Then just repeated step. Patterned has sight to download instructions from. It made it really simple.
Parts Used:
-
Jeremy from Gerrardstown, WV
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Socket set
Was this instruction helpful to you?
Thank you for voting!