Models > 11062702100 > Instructions

11062702100 Kenmore Dryer - Instructions

All installation instructions for 11062702100 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11062702100
1,771-1,785 of 1,883
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

drum rollers worn out, making kocking noise

  • Customer: Nita from Clarkston WA
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
just replaced the rollers with the new ones. The trouble was getting the belt around the drum again, but it all worked out and the dryer is running good

My daughter threw a heavy wet comforter into the dryer and the tri-ring sheared off.

  • Customer: Joe from St. Louis MO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.

Unusual noise

  • Customer: Ingrid from Orland Park IL
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Watched the videos for unusual noise... they are great and saved me time with advice how to open the machine from top and front and install belt on tension wheel. Lower roller bad, replaced both. Opted to also order and replace the belt and rear seal upon inspection. Time spent would have been 30 minutes or less but rear seal replacement requires time to clean off old seal adhesive and glue on new one. Take your time with rear seal replacement it takes longer than I thought but worth it. The labor involved to replace the seal alone would have been more than the dryer cost new. Also- I ordered parts at 2pm std shipping option and got them THE NEXT DAY less than 24 hrs later. May not be typical depending on your location but I was amazed. I have been fixing all my own appliances for years first time customer with Parts Select. Oh and EACH of the 3 parts ordered were 10$ less EACH than my local parts guys. WOW

Replace Rear Seal on Drum

  • Customer: Elizabeth from Myrtle Beach SC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
First unplug the unit and move to an area where you will have enough room to pull the drum out. I opened the top by sliding a screwdriver in the top left and right edge and popping the clips to allow the top to lean up and back against the wall. I tried to unclip the harness for the door switch but couldn't get the harness to release and instead took out the two screws holding the door switch in place. This is located on the top right inside the dryer door. Once the switch was off I was able to use the socketdriver to undo the two screws on the inside top left and right to release the front of the dryer by pulling up easily and unhooking the bottom front. I was then able to set the front of the dryer aside and begin removing the belt from the tension wheel and motor. Pay close attention to how the two are connected because it will confuse you putting it back together.The belt feeds through the tension wheel and when you release it the tension wheel is just sitting in place and may pop out of place. Remember which slots it sets back into for when you put the dryer back together. We removed the drum, checked the two rollers to make sure they were in good working order. I removed quite a bit of debris from them. Once the drum was out I pulled off the old seal. Took a piece of sandpaper to rub away any excess old adhesive and began installing the new felt seal. Follow the directions carefully to ensure that the seal is sitting on the edge properly before you begin applying adhesive under the edge. I had someone helping me to install the seal but probably would have needed clamps to hold the seal while working it on. It's not a super tight fit but is fitted and once you start putting it on it easily slips off the other side. A couple clamps would hold it in place if you don't have someone to help. Once the seal is on and you apply the adhesive you begin putting the drum back into place first by slipping the belt back over the drum where it can hang until you are ready to put it back on the motor. You have to make sure the seal isn't folded under the back of the dryer. Again a little tricky but if you gently spin the drum slowly counter clockwise a few times you can work it so it's not folded under. Once you see everything is in place you can reconnect the belt through the tension wheel onto the motor. Check drum again by spinning counter clockwise. Install the front of the dryer back on by setting it into the bottom clips. Put the top screws back in. Re-install the door switch making sure it's back in place with the tab sticking through the hole at the top of the dryer door. Bring the top back down. Close the dryer door and plug it back in and everything should be good to go. It wasn't a difficult job at all and I would probably attempt other repairs now that I've done this one. Beware the adhesive is kind of watery when it comes out but you don't need to use a lot under the edge of the seal. Good luck with your repair. I am thankful that PartSelect was so easy to order my parts from and I got the part within a few days. Thanks!

squeaky dryer and already replaced everything else

  • Customer: Melia from Quincy FL
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
I watched several Youtube videos for this repair. The best showed a man taking you through every part of replacing the rear felt seal. I used binder clips from my home office and he used clothes pins to keep the seal in place while gluing it and letting it set. To completely finish this repair, it takes over 24 hours to get your dryer ready for drying again. Steps to repair: you need to get to the dryer drum, watch a video on how to do this to include taking off belt, idler pulley. Remove Drum from the dryer. take off all the old felt seal. take out new felt seal and place around the drum, it will be pretty tight. secure the seal by using clothes pins or binder clips all the way around the drum. this will help you keep the seal on the drum and guide you as you use the glue to bind the seal to the drum. Using the adhesive provided with the felt seal, going around the drum, glue down the seal and re-clip it so the glue gets a good grip. let dry of at least 1 hour. Cannot use the dryer for another 24 hours to make sure the glue dries completely and is ready for the heat. I had already replaced the 2 rollers, 2 shafts, belt, idler pulley and start switch and dryer still squeaked. Then I replaced the rear felt seal. NOW I am replacing the bulkhead because it is worn flat in some places and is warped. I am waiting on the part.

Washer overflowed

  • Customer: Beth from Valley Springs CA
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Once I watched a YouTube video showing me how to do the job I ordered the part from you. Am so impressed with your fast shipping and best prices via the Internet. Thank you SO much! The water level switch was easy to install, it ws getting the cover on the washer back on that was hard for me since I am 68 yrs old and have a bad knee. Its why it took me two hours to do what most people could do in 20 minutes.

Dryer would not start

  • Customer: Marianne from Solon OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
My dryer is a KitchenAid KEYE660W (electric). I tried to start the dryer but it would not run. I did notice that if I held the start button down, I could feel light vibrations through the button. Searched through Yahoo and this site and determined that this is often a bad Thermal Fuse. Used the diagrams on this site to locate where it should be, removed the back of the dryer with a screwdriver, removed the two wires clipped to the Thermal Fuse and unscrewed the Thermal Fuse. I had a friend test the fuse with a Multimeter. It was bad so I ordered another one on this site and it arrived in two days. Screwed the Thermal Fuse back in and clipped the two wires back on. Started the dryer and it worked!!! Replaced the back of the dryer. This repair took 15 minutes MAX and taught me a little bit about Mulitmeters.

Took to long to dry clothes.

  • Customer: Larry from Sierra Vista AZ
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Replace the heating element and themostats. Saved me $$$ from me buying a new dryer. Thank U for the videos also. Great help.

The leveling foot on my dryer broke.

  • Customer: Diana from Clifton NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
We only had to tilt the dryer enough to be able to screw the leveling leg in place.The only hard part was holding the dryer steady to screw in the leveling foot.

ice tray was broken

  • Customer: mike from fitchburg MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
This was by far so easy the instruction Partselect gave me where right on step by step. a repair man was going to charge 75$ just to come out 9$ from partselect. Thank you very much Mike chaplin

No dryer light, and dryer would shutdown randomly

  • Customer: Charles from Castlewood SD
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
ordered a replacement light - took about 5 minutes, hardest part was disconnecting power and getting into the dryer replace light. The second part was replacing the dryer switch. This took a bit longer, but was completed. The plastic locks on the top were a little different than the video, but once I saw how the one worked (one side popped open very easily) the other one just took a bit of nudging and opened easily too. Now that I have done this, I am not afraid of working on it for other issues. Great helpful site. They will have my business for other repairs.

wont shut off &no light

  • Customer: RUSSELL from POUGHKEEPSIE NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
remove top &replace switch

Door switch broken, light out

  • Customer: Jonathan from West Bend IA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Very easy replacing these 2 parts. Simply unscrew the 2 screws under the lint trap on top and pry open the front top of the dryer (it'll open like a hood on a car). Then just unscrew the 2 screw holding the switch on by opening the dryer door and unscrewing on the switch- unplug the old switch. Installation reverse of removal! For the light, just 1 screw takes the pate off and screw the light in like a night light bulb-- EASY!

dryer did not stop when doors was open and light was not on with door open

  • Customer: Maria from Whitestone NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
your video was so helpful. It was exactly as shown. Thank You,we just had to replace a 14year old dishwasher and a 20 year old refrig. so it was great to repair the dryer.

Dryer would not start.

  • Customer: Sam from JOHNSON CITY TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took back panel off. Did not have a clue! Went to Partselect Web site,entered my problem,BAM! instant solution.Watched repair video and was surprised how simple repair looked.Heck I can do this,no problem! I work from 7 A.M. to 5 P.M. so theres no chance to stop by local appliance part store before they close. Ordered my parts from Partsselect,arrived in just two days. Followed video instructions ,completed job in thirty minutes or less! I also got important information regarding maintenance and cleaning dryer to prevent fire hazard.Thanks,for help and saving me time and money.When I have a problem in the future I now know where to go.
All Instructions for the 11062702100
1,771-1,785 of 1,883