11062612101 Kenmore Dryer - Instructions

I watched your video on how to replace the fuse.Wow it was a lot easier than I thought.I would highly reccomend anyone to watch the video before even trying to do any repairs.The dryer is working like a new one.By doing it myself saved me a lot of money.Thank you

Removed two screws at the top, removed two screws for the front panel, removed the broken belt, installed the new belt, followed the directions that were in the new belt package, and replaced all the panels and tested. It worked.

What a pain in the butt to route the belt thru the tensioner! There's room for only one hand in there. The guys who do this for a living must have some secret. My solution was to drill a 3/16 hole thru the side, make a j-hook from 8-32 threaded rod, use that and a wing nut to pre-load the tensioner, route the belt, then slowly back off the wing nut until the belt was tight. It works. . . .

Replaced the part. It just slid right in to the appropriate space on the dryer.

first I unplugged the dryer. Then I removed the back of the dryer with a 1/4" nut driver. with the back off using the same 1/4" nut driver I removed the one screw that holds the cycling t-stat slowly remove the t-stat and take one wire off at a time and plug it onto the new t-stat once all wires are replaced. place the t-stat back in and secure with the screw. Then put the back of the dryer back on. put the dryer vent hose back on. plug in and away you go. repair done. If that doesn't fix it. Then the next step is probably to check the gas valve coils. That is a little more difficult repair but not to hard.

Remove back pannel heating element easy to replace. Partselect has the best service ever...

Watched several videos online and was suggested that the thermal fuse was bad, so i replaced it but no fix. So i checked the previews Q&A from other costumers and watched the videos on how to replace different parts. I first looked thru the peep hole on the bottom left part of the dryer and saw the igniter glow for about 10 sec every minute but no flame would start. So i replaced the igniter, the flame sensor, and the coils all at once. I know thats not the proper way to troubleshoot something but i was gonna take the drum out and everything so mind as well replace them all. Dryer works like new and dont have to listen to the wife complaint anymore!!!

Pop off the top , Then one screw holds each side . slide belt around drum and then preload tensioner as per instructions . Simple!

The video is right on. You can't go wrong, and I don't consider myself a handyman at all.

I replaced both the Thermal fuse and Cycling Thermostat, both of which cost less than fourty dollars. just removed the back panel, and replaced the parts in less tham a minute. Replaced the back panel. Job done.

Super easy repair. Just removed the back panel, took out the old heating element, plugged in the new one and put it back together. I had also replaced the element in a similar Whirlpool dryer in one of my rental properties a few months ago and it was just as easy. Between the two repairs I saved between $200 and $300 in repair labor. PartsSelect always has the parts I need in stock, ships quickly and their installation videos rock. I have also used them for repair parts on microwaves & refrigerators in the past. Excellent vendor. Highly recommended.

viewed the video that was posted on your web site it was very use full in helping me to repair the machine. it was not difficult to take out and reinstall.i like your quick response on shipping parts. I am very satisfied.

I tested heating coil and it was good so I replaced sensors and now works like new again. And while I was at it I cleaned out my dryer vent.

My wife hates me because I keep repairing our appliances. The dryer and washing machine are now 21 years old and look like new. To replace these two parts, first check if the igniter is glowing at all when you turn the dryer on. To do this remove the access panel in front on the bottom. To remove it, slide a flat screw driver across the slot onto of the panel to locate the release clips. Depress the release clamps by sliding the screw driver on top and pull the panel forward. Now start the machine and see if the igniter glows. If not proceed to replace the Thermal Fuse and both thermostats. To do so, open the back panel of the unit. First disconnect power and vent. Unscrew and replace components which will be easily seen on the bulk head. Use a pliers to remove the contacts. Your machine will now last another twenty years and your wife will hate you as does mine:)

Took the back cover off. Replaced fuse and put the cover back on. Worked great.