11062612100 Kenmore Dryer - Instructions

Easy to follow videos on your site made this repair a breeze. I ended up having to replace the high temp cutoff as well but for 60 bux my dryer works like new. The repair man wanted $100 just to come look at it. Could not have done of without the easy to follow video.

ordered the part recived the parts and installed the part that easy. saved us lots of money did not have to buy a new dryer.

I thought I would do it myself and figured that because it wasn't heating I would replace all the thermostats and thermal fuse. Because I wanted to get it going right away, I also ordered a timer just incase. Turns out it was the timer and not the thermostats or fuze. I have a virtually new dryer again. Replacing the parts was really easy and didn't take long. Word of advise is to use an electrical (ohm) tester to determine which part is faulty; this will also save money by not buying not-needed parts.

Removed the back panel with a 1/4" nut driver on a Ryobi impact driver. Used multimeter to check the thermal switches and the heating element. The element was broken. Went to the PartSelect web site and quickly found the part by using the model number and verified the right part by comparing the photos to the actual part. Placed an on-line order at approximately 1:00 pm and the part arrived at 2:00 pm the next day. Cleaned out the dryer vent and it works better than it has in a long time. Great web site and delivery from PartSelect and didn't have to run around town looking for the part.

I followed exactly the video. It really was that simple. My 5 year old even helped me unscrew the nuts. The Thermostat was on the lint shaft and unscrewed easily. Once out I removed the wires. The hardest part was removing the wires, They were really tight. I replaced the wires and screwed in the part. Before I replaced the back I cleaned out the lint tube and turned on the dryer. I saw the flame and the heater kicked right on. I replaced the back and was done. *****However the next time the dryer went the heat didn't remain on and turned off too soon. I did some more research and found you usually need to replace the thermal fuse at the same time on Whirlpool units. So I have ordered the part and will let you know if kept the heater from turning off too soon.

Learned that my Kenmore dryer was actually a Whirlpool model. Removed kick plate in front of dryer. Removed the cover to the blower wheel. Cleaned out Dryer with vacuum cleaner. Used a multimeter to check for continuity on all thermostats, fuse, and heating element. Decided it was the cycling thermostat. When ahead and replaced the fuse at the same time. Checked out the installation video on this site, wwwPartselect.com ( it was very helpful in understanding how to remove the cycling thermostat - needle nose pliers helps in pulling of the connect wire clips - knuckle buster). Ordered next day delivery. The parts were on my front door early next morning FEdEX ( i live in the very corner of the NW US). Nice!

(Always unplug dryer before making any repairs) I opened the dryer and checked the heating element. Making sure that the connection was good and nothing was damaged, I determined the problem was overheated wires. They melted and lots connection. I replaced them with the heating element wire connection kit. Easy to install and simple to get right. I cleaned the dryer again with a vaccum cleaner, removing all the lint, and checked the vents, making sure they were clear...I turned the breaker on (it was tripped when the dryer overheated)and everything worked great.

The video you had of my dryer was different then my dryer and the pulley was in the middle of the bottom and the motor and fan were in front of it. I had to replace the belt without being able to see what I was doing. I couldn't get it at first then realized there was tension on the pulley wheel and had to pull it towards the other wheel in order to get the belt on there. Once I pulled the wheel it went on really easy. My first time working on a dryer but I knew I could do it myself.

removed the back panel,propped up the top, and removed the front panel, and replaced the rear seal, the belt, and idler pulley, and put back together the opposite of taking it apart.

instructions were clear and repair was easy

Well, to Figure the issue I took the entire thing apart. Actually a lot more than needed. I found the torn belt and ordered it. I did not realize I may need a new belt tensioner which is sold with a wheel for the belt to wrap around and be tensioned by. Actually the original just utilized a rubber c or u shaped design(no wheel) for the belt to slide over. Anyways, instead of ordering and waiting for a new wheeled belt tensioner, I installed new belt with all original parts and working fine. I did oil up the drum rollers to reduce noise. And since I took the whole thing apart I cleaned the lint from every place it could hide. Ps a coke can is said to be helpful to hold the drum up while installing the belt but I found a jug of laundry detergent did better. Totally easy project for someone with no appliance repair history

The broken belt was found when I opened the dryer. The part number was on the belt and a quick online search led me to PartSelect. The part was available, delivered in less than 2 days and there was an online video showing the entire repair in detail.

My ground wire in my electrical box was not connected.

Step 1: remove new latch from bag in which part comes. Step 2: push latch into hole where the other latch was. Step 3: enjoy having a dryer you dont have to hold closed with a folding chair.

Unplug Dryer. Take off exhaust hose. Unscrewed the back panel and remove off the dryer. Locate heating element and unhook wires. Unscrew heating element. Replace with new heating element. Hook up wires. replace panel and exhaust hose. Plug dryer back in. Check for heating.