11062612100 Kenmore Dryer - Instructions

Went to YouTube It was real easy.

I ordered the part, watched the video and made the repair in less than thirty minutes. This was much cheaper than purchasing a new dryer.

Took the back cover off the dryer and replaced the heating element with the new one put the back on connected the vent hose and done . Have smiles now, saved money.

Pull off the front panel of the dryer, and replaced the thermal fuse. Very easy. Plus, vacuumed out the whole inside of the dryer, the rear and the tube running from the dryer to the outside. Will be doing this at least every 3 months to be safe. You would be surprised at how much lint builds up inside the machine. Eve though we clean the filter trap after every use of a load of clothes.

Repair went fine. Really easy for the most part. Unfortunately it didn't solve my problem. Great place to get parts though. I'm going to continue my search for the source of the noise

Thank you for the the installation tip I received along with the part. The suggestion of removing the front panel to install the belt made the installation go very smoothly.

I unplugged the dryer then removed 2 Phillips screws from lint trap. Then I popped the top up on each top corner with a screwdriver. I removed the 2 screws holding the front cover. I unclipped the wiring connection and moved the panel. I took out the old belt, put the tensioned back on then put the new belt around the drum and held the drum up with my shoulder then put the belt through the tensioner and put it on the motor spindle by pushing the tensioner back. I put it back together and it worked perfectly. Your video was very helpful. Job was very easy.

Had my wife call the repair man. Since it was Saturday afternoon, no luck. YouTube help me diagnose the problem. I found that the drum belt slipped off the idler pulley assembly and the assembly was laying on the floor. I noticed that the belt was frayed and was probably stretched out which may be why the belt slipped off in the first place. I glued the frayed pieces of the belt back with gorilla glue and clamps. You Tube helped me mount the idler pulley assembly and string the belt correctly. I then ordered the replacement parts through your website. The parts came to my home in a few days and I will fix the dryer properly when I get a chance.

The instruction sheet that comes with the parts is excellent. Follow it and all goes well. Be patient and stay away from the sharp sheet metal edges present in all such appliances !!

First bought the Cycling Thermostat and Thermal Fuse. Installed. Still did not work.Next bought the Thermal Cut-Off Switch and the High Limit Thermostat. Installed. Still did not work. Then purchased the timer and installed. Still did not work. Finally tested the heat element with an on/off switch and wire. The heater worked. Changed the 2-pole 30 amp switch in panel box and the problem was solved. The parts were reasonable and easy to install. I left the new parts in and saved the old oned for the future, Parts delivery was quick. Will use parts Select in the future.

Watched the video and followed the directions. It was pretty easy, but, I ended up having to call the repairman anyway. After the heating element was put on we put the cycling thermostat on. I didn't know it, but I put some wires on upside down. I bought a heating element, a cycling thermostat, thermal fuse, and a thermal cut off kit. All that, and I still had to pay a repairman. If you're good with wires, or have some knowledge of appliances this is an easy fix.

Diagnosed problem , orders parts . Installed parts

What a pain in the butt to route the belt thru the tensioner! There's room for only one hand in there. The guys who do this for a living must have some secret. My solution was to drill a 3/16 hole thru the side, make a j-hook from 8-32 threaded rod, use that and a wing nut to pre-load the tensioner, route the belt, then slowly back off the wing nut until the belt was tight. It works. . . .

Replaced the part. It just slid right in to the appropriate space on the dryer.

first I unplugged the dryer. Then I removed the back of the dryer with a 1/4" nut driver. with the back off using the same 1/4" nut driver I removed the one screw that holds the cycling t-stat slowly remove the t-stat and take one wire off at a time and plug it onto the new t-stat once all wires are replaced. place the t-stat back in and secure with the screw. Then put the back of the dryer back on. put the dryer vent hose back on. plug in and away you go. repair done. If that doesn't fix it. Then the next step is probably to check the gas valve coils. That is a little more difficult repair but not to hard.