Models > 11062202100 > Instructions

11062202100 Kenmore Dryer - Instructions

All installation instructions for 11062202100 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11062202100
1,171-1,185 of 1,248
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

dryer belt broke

  • Customer: LAWRENCE from BANDERA TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
belt # 346995. part was delivered quickly. Part fit perfect, no problem. there was a video on youtube how to replace it. It took about 25 minutes from start to finish to install. works like a new one. Thanks partselect.

Drum was not turning when the start button was pushed while morot was running

  • Customer: Philip S from Springfield VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
After I received the new belt I un-plugged the electric cord and shut off the gas supply. I pulled the dryer about 10 inches away from the wall to remove the vent duct from the back of the dryer. Used the putty knife to release the clips on bottom front panel and a screw driver to pop the front of the top at the left side and right side, removed the two Phillips head screws under the lint door, then lifted the top to the vertical position. Loosened the hex head screws at the bottom of the upper front panel (don't take them out). At the top back side of the front panel, pull off the electrical wires from the door interlock switch and pull the retainer holding the wires to the front panel (don't take the plastic clip from the wires.) Place some wood blocks to support the drum at the front of the drum. Use the nut driver to remove the two screws on the inside at the top of the front panel. Disconnect the two springs that hold the door closed. Lift the panel from the two loosened nuts at the bottom and pull it away from the drum and let the drum settle on the blocks of wood to support it. Place the new belt around the drum lining it up where the old belt left its mark around the drum with the grooved surface facing the drum. Replace the front upper panel with the door to engage to two tabs on the screws you left at the bottom. Lift the drum so that it engages with the opening in the front panel. In case where the drum had dropped too far, use the putty knife to engage the felt flange at the rear of the drum with the rear cabinet flange. Reinstall the two screws at the top that you had removed. Reconnect the two wires at the interlock switch and snap the clip with the wires to the flange of the upper front panel. Replace the door springs on the hinge extensions to the flange at the bottom of the cabinet. Set the Idler pulley assembly into the cabinet floor sliding the end tab into the slot and the two tabs fit into the holes in the floor. Pull a loop of the belt under the idler pulley and then pull it toward the motor pulley. You might use the shaft of your Phillips screw driver instead of you fingers to get it around the pulley on the motor shaft. Turn the drum by had for several complete turns to ensure that the belt lines up on the drum and that the drum isn't binding on the back or front seals. Close the top, snapping onto the top of the cabinet. Plug the dryer into the electric outlet and set the timer to Fluff Air range and push the start button with the door closed. The drum should be turning smoothly. Open the door and all should stop. Reconnect the Vent and move the dryer back to its former position. Turn gas supply on but do not start the dryer. Check for gas leaks. If you find a leak in either at connectors or the flexible connecter call a qualified contractor to replace the flex connecter. Otherwise you can then set for one of the dryer settings and push the start button and observe the burner through the lower panel to see that the igniter is lighting up and finally the gas turns on and a decent blue flam is burning in the combustion tube. Open the dryer door and the flame should cut off and the drum stop turning. You are ready to set the bottom panel. Set the panel on the two lower tabs and close it upward until the snaps lock it in position. Job Done

Broken belt

  • Customer: Christopher from Skillman NJ
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Used PartSelect instructions for routing belt & a customer's valuable guidance.

Drive belt very warn, not broken

  • Customer: Philip from Cambridge MN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I removed screws for the lint screen - TOP. Pry up top with screw driver. Disconnected inside top front 2 screws, removed door control wires, white and blue. Lift off front of dryer. Tip dryer back about 40 degrees against wall. Remove warn belt (not broken). Relocate idler bracket on the cabinet base, follow diagram which comes with the belt package. Be very careful that the belt is NOT on the side of the idler roller. I had to do this install a second time, because I had it wrong the first time. Even though I've done this repair 5 or 6 times, there's always a first time GOOF. Not really a hard job.

Broken dryer belt and idler pulley

  • Customer: Anita from Keokuk IA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Threw away the printed instructions and followed the Part Select video ,featuring Steve...

Belt broke

  • Customer: Brunner from Sykesville MD
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Watched a you tube video on replacing a dryer belt for a whirlpool dryer. Perfect instructions. Dryer is working great.Thank you

broken belt

  • Customer: mark from merrick NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
video on your website made it super easy

Broken belt on dryer

  • Customer: Robert from Lauderhill FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
This is a straightforward repair that you can do in an hour or less. Open the lint trap and remove the two screws. Use a screwdriver to pop up the top of the dryer. Remove two screws that attach the front panel. Now you can lift out the drum and then lift off the front panel. Clean out all the lint. Make sure the motor pulley turns smoothly. Tilt back the dryer diagonally to make the rest go easier. Loop the new belt around the drum (rubber side down) and reinstall the drum against the back wall of the dryer. Make sure the cloth liner fits perfectly around the ridge, with no folds so the drum rotates easily. Make sure the drum fits smoothly against the two rubber positioning wheels on the back wall. Position the new belt around the center of the drum. On the dryer floor, stand up the tensioner bracket. Tricky part -- thread the belt so it runs through the bracket and loops around the drive pulley on the motor, rubber side against the pulley. The belt should be tight, held by the tensioner. Reinstall the front panel so the opening aligns with the drum opening. Drop the top down, snap into place.and reattach the screws in the lint trap. Done!

Broken Belt Tub wouldn't turn

  • Customer: Leslie from augusta WV
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
TURN OFF POWER TO DRYER............................. Pay attention to where everything is as you take it apart, so it can be put back the same way. Take out the two screws by the lint screen. Use flat tip screwdriver between space in front of top to help lift top. Use rag on tip of screwdriver so as not to scratch it. Take out two screws inside the front panel at the top. One on each side. Unhook the switch wiring. Lift up the front panel to take off. The tub will be loose, so it can be taken out to inspect other components. Some call the tub a drum. Be sure to see how the belt tensioner is attached, so it can be put back on the same way, if it comes loose. It is under the tub. Take out old belt. Put new belt around tub. Make sure the tub sets on the two rollers in the back of dryer. While holding tub, put the belt around the grooved pulley on the motor. Grooves are face down against the tub. Feed belt through the tensioner. Put the bottom of front in on the tabs. Be sure belt is still in place around pulley and tensioner etc. Hold tub through front door and close front. Put the two screws back in on each side. Close top and put the two screws in at the lint screen. Done. Turn power back on. Turn on dryer to see if it operates properly. If not, check out your repair to see if everything is connected properly.

Dryer wasn't turning.

  • Customer: Annemarie from High Ridge MO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Well my husband did the install and he said it was very easy??

dryer tub drive belt broke

  • Customer: Ray from Salisbury NC
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unplugged the power cord. Removed two screws on lint vent , used putty knife to release clips to raise top at front of unit. Disconnected the plug from front door switch. Laid dryer on its back. Removed two screws to remove front including the door. Vacuumed lint from inside unit. Installed belt temporarily using two pieces of masking tape to hold it in place while properly routing the belt. Gave the tub a full turn to insure alignment.. Reinstalled the front of unit with the two screws. Righted the unit and snapped down the top. Replaced the two lint vent screws. Plugged it back in and done! Piece of cake!

Replaced Belt

  • Customer: MARCUS from MACON GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The online vidio was very helpfull

belt replacement

  • Customer: David from Paris TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
first I took a flat head screw driver to pop the top of the dryer open, and then removed the screws from the lint tray. Next I lifted the lip back making sure it was supported by the wall behind. Third I removed the front of the unit by removing the bolts attached on both ends of the top of the unit. I then opened the door and removed the screws on the right top side of the lining of the door to the switch. Then I carefully held onto the tub while lifting the front face of the unit to remove the face of the dryer. After carefully removing the face I released the tub and set it aside. Then I picked up the tension pulley set it back in its slot followed by placing the belt rib side down around the tub. Next step was to place the tub back in the unit making sure the felt was in place and then I ran the belt back through the tension pulley applying tension in order to get the belt back onto the motor making sure the ribs of the belt aligned up with the ribs on the motors belt drive wheel. After completing that I then grabbed the front panel of the dryer unit and gently replaced the panel making sure that the slots and hooks lined up while placing the tub back in alignment of front panel. Once that was complete I replaced the screws in the door switch followed by replacing the bolts in the inside of the top comer of the front panel till hand tight. Last but not least I slid the lint tray back in place in order to make sure screws did not fall in to the hole the lint tray occupies. After replacing the screws I then plugged in the dryer gave the tub a few spins with my hand to make sure it was in place correctly I gave it a test drive by leaving the door open and pressing the door switch shutting off the light in the unit so it since the door was shut and turn the unit on for a cycle for at least one minute to see if the tub rolled freely on its own. All was good and only took 12 minutes to change and replace part. Easley can be done by any DIY first timers. Me I work with all kinds of units but the older units are easy and no need for a tech I promise.

Belt of the Dryer broke

  • Customer: Sharon from Reinholds PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I watched the video and did the repair myself. My husband, who works in maintenance, was IMPRESSED! Yay! Thank You!!!! Love you guys! I am forwarding your website to my children!

broken dryer belt

  • Customer: JERRI from MONTICELLO FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
i popped the top off. removed the 2 hex screws in the front upper inner corners. lifted the front panel up about an inch n removed it. pulled the drum out. removed the old broken belt. put the tention roller back into the slots at the bottom panel n base of the motor. mounted the new belt around the motor n thru the tentioner as i placed the drum in position n mounted the belt around the drum. holding the drum in place i replaced the front panel. replaced the hex screws n closed the lid. wah-lah. dryer fixed... thank you parts select
All Instructions for the 11062202100
1,171-1,185 of 1,248