All Installation Instructions for Kenmore Dryer 11062202100

wasn't producing heart

The thermostate and one of the wires were burnt. Ordered a thermostate and re wired the connector to the wire. All I had to do was replace the thermostate and connect the wires to it. Took me probably 15 to do it all :)

Parts Used:

Dryer High Limit Thermostat

Kayley from puyallup, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Wrench set

Was this instruction helpful to you?

Thank you for voting!

Dryer would not run or start at all. Seemed like it had no power but the light still worked and it wasn't the breaker.

Took 12 screws off the back. One screw for the fuse. $9.32 and 30 minutes and we're back in business!

Parts Used:

Dryer Thermal Fuse

Joshua from Sturgeon Bay, WI
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Broken belt

Followed the instructions that came with belt everthing went just fine.

Parts Used:

Multi Rib Belt - 92-1/4"

Rick from Emporium, PA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Dryer would only run for a few mins and then not restart. Also there was a grinding noise.

I replaced the entire motor in the dryer and the belt while I had it open and it is working great! I just watched the short video on the site to learn the tricks and did it myself.

Parts Used:

Drive Motor with Pulley

Andrew from Lawrenceville, GA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Starter would not stay on after pushing on

Followed video, very easy installation. Unfortunately, the new starter switch does not stay on either so we still have not resolved the problem.

Parts Used:

Push-To-Start Switch

Rosemary from Ellicott City, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Gas burner would not fire.

First removed and checked the ignighter. It was fine. Next I located the schematic drawing and discovered that the burner, ignighter, and flame detector were all operated by one simple 110 volt circuit. This circuit did not power up when the dryer was cycled on. I pulled the dryer from the wall, removed the back panel, the vent etc. I then located the operating thermostat and the thermal fuze. The thermal fuze was open. (GOOD NEWS AN EASY FIX!!!) Thanks Guys

Parts Used:

Dryer Thermal Fuse

Leif from Plainfield, IL
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers, Socket set

Was this instruction helpful to you?

Thank you for voting!

The control panel won't leave Casual load.

Well the video showed us taking off the back. Which wouldn't come off. Welded. Then we could not find the fuse in back of the unit or bottom. The second time we tried we found it in the front. We had to take off the front, bottom cover then we found the fuse. But, it didn't fix the problem. The unit is still on Casual load only. When we push the buttons the other lights light up but goes back to Casual. The unit is clear of lint and still drys but only at the Casual setting.

Parts Used:

Dryer Thermal Fuse

Ann from Cincinnati, OH
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers

Was this instruction helpful to you?

Thank you for voting!

The dryer belt broke.

I watched the attached video that was with the belt I ordered and it took less time to do the repair, then it did to watch the video. The video was very helpful.

Parts Used:

Multi Rib Belt - 92-1/4"

Bill from Cooper City, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Motor hum on start-up

Trouble shot to failed motor. Ordered motor and new drive belt. The hardest part is figuring out how the dryer dis-assembles. Follow Parts Select on-line instructions. Also, several good instructional videos on You Tube! My recommendation is to order a new "blower wheel" when changing motor on a gas fired dryer. The heat combined with age bonds the blower fan to motor shaft. It had to be broken off in pieces to remove motor.

Parts Used:

Multi Rib Belt - 92-1/4"

Drive Motor with Pulley

GREG from BLAIRSTOWN, NJ
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)

Was this instruction helpful to you?

Thank you for voting!

Belt broke tub did not turn

took off the broken belt and the idler pully went to the internet found your website watch the video and ordered the parts got the in 3 days took 15 mins to put them on and all is good

Parts Used:

Idler Pulley Assembly

Multi Rib Belt - 92-1/4"

Larry from Clute, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Thank you for voting!

Belt popped

2 screws at lint tray 2 screws on back pick up top 2 screws in front under top lid separate front from drum slip in new belt screw front back to top route around tension pully put other 4 screws in complete so dry something

Parts Used:

Multi Rib Belt - 92-1/4"

Wade from Labadieville, LA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Thank you for voting!

Broken belt

Popped top up Took front panel screws out. Looked for other damage. Put belt around the tumbler and got it hooked up. Grew an extra set of hands and re assembled front the checkd seals to make sure they where on and put top back down... Process is a pain in the butt i reccomend socket set channel lock pliers and a cold beverage or two

Parts Used:

Multi Rib Belt - 92-1/4"