Models > 11062064100 > Instructions

11062064100 Kenmore Dryer - Instructions

All installation instructions for 11062064100 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11062064100
376-390 of 409
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Stopped and would not restart / start.

  • Customer: Patricia from Duck WV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
1)Shut off power supply to dryer. 2)Removed lint filter. 3)Removed two screws that secure filter duct to dryer top. 4)Lifted front of top to gain access to door switch. 5)Removed two switch mounting screws. 6)Removed the two power leads. 7)Reconnected power leads to new switch using "Normally Closed" terminal on switch. 8)Reversed the previous procedures to complete repair.

Idler pulley bearing was sqealing

  • Customer: David from El Paso TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Disconnected the power and duct from the dryer. Removed the back and top of the dryer by removing the 1/4" screws. Created slack in the belt by compressing the spring and moving the idler arm.Slid the belt off the pulley. Removed the tri-ring clip, slid the old pulley and gasket off. Cleaned and inspected the shaft and vacuumed the inside of the dryer. replaced the gasket, pulley and tri-ring clip. Replaced the top and back of the dryer. Connected duct and power.

not drying clothes

  • Customer: gene from leesburg GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
The repair was easy and very simple. With nut driver removed front cover. Noted the wiring set up and removed. Lifted heat tunnel up and pulled it from the case. Removed the old heating element and install new one. Reinstalled the heat tunnel reconnected the wires. Slide tunnel back into position. Replaced screw and you are done. I always pray and ask Jesus for his help and things always go well.

Dryer won't get hot

  • Customer: Dan from Port st lucie FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Unplugged unit. Took off the lower kick plate took the old element out and put the new one in. Works great.

Dryer element burned out. Dryer would not heat.

  • Customer: Cassandra from Idaho Springs CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
I was afraid I had to go in from the back panel, undo a million little bolts, after pulling the whole thing out far enough to get behind the dryer. Not so! I watched the installation video. I cannot get to the 220 plug easily so I turned of the switch at the breaker box. I opened the small panel on the front of the dryer under the dryer door. Loosened one bolt on a cover guard to expose the element. Unplugged the connection to the element and easily pulled out old part. Slipped in the new part, reconnected the little plug connections, closed cover panel.! Voila! Done! My Husband was amazed that I was done & we were ready to go again & my grand kids cheered for me!! 15 minutes or less instead of hours.

No heat in dryer

  • Customer: Brian from South Milwaukee WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Ordered the kit for my dryer. Popped off the front access panel and 4 screws later, dryer works perfectly. 28 dollars plus shipping and fixed. Great OEM parts and fast shipment from Peoria. Recommended.

Door latch mechanism broke and fell into door

  • Customer: Peter from POTTSTOWN PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Step 1: remove new latch from bag in which part comes. Step 2: push latch into hole where the other latch was. Step 3: enjoy having a dryer you dont have to hold closed with a folding chair.

Dryer had a high pitch squeal, first at startup, then during full cycle.

  • Customer: Dustin from Rochester MN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the top panel of the dryer via a couple of screws from the rear. Remove the rear panel swing it open light a door to the right, minding the electrical connections. Removed the belt from the pulley, removed the Tri-ring from the shaft and slid the pulley off of the shaft. The shaft was slightly rusted so I used a steel brush and brake cleaner to clean it up, placed the new gasket, pulley, and tri-ring on, replaced the belt, and put the panels back into place. As the dryer is about 7 years old, also removed the front lower panel and cleaned out unit which had quite a bit of accumulated dust and glitter especially in the vent lines. (3 girls live here). Pretty easy, most screws remove with just the one tool.

felt gasket had come loose!!!!

  • Customer: Charles from Phoenix AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
remove&replace

dryer would not run

  • Customer: paul from MOUNT CLARE WV
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
After disassembling, I orderedparts.was told it could be the thermal fuse.found that the belt was broken.disassembly was simply removing screws, but as a novice, it was difficult to determine what to remove and how to remove only what was needed.after watching your video, it was much easier.replaced thermal fuse and belt.made sure to clean lint from motor and interior of dryer as well as vent lines and vent blower.the old machine works fine, until something else goes.

Door Switch Actuator Spring/Lever & Door Catch Replacement

  • Customer: Charles from Marysvile WA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Open the top and replaced the switch bracket with the actuator lever then inserted new door catch.

Dryer runs but no hot air

  • Customer: Larry from Newnan GA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 0 of 0 people found this instruction helpful
Disconnected power from dryer (safety first)! Removed bottom front panel (two screws hold it in place). Then remove the two screws that hold the sheet-metal bracket/guard in place in front of the heating element. Disconnect the two wires from the heating element terminal (white stripe wire is on top, remember for re-install purposes). Remove screw that holds heating element in place. Remove heating element from the vent housing. NOTE: The old heating element will be difficult to remove, it's a tight fit AND there's a spring on its' side that holds it tightly in place...beware that the edges are sharp; I used a pair of pliers to pull the element out in order to protect my hands. Once the old element is out, put the new one back in its' place...again watch out the edges are sharp and the element fits tightly into the vent, so if you have mechanics gloves now's the time to put them on to protect your hands, as the edges of the vent and element are sharp. Once the element is into place, secure into place with screw on left side, re-attach wires (white stripe on top terminal), put the guard back into place, close up the bottom panel, and power up.

did not dry ths cloths

  • Customer: karl from grand rapids MN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
removed front lower panel and removed 2 hex screws 1/4" on front of heater tube support unplugged 2 wires hooked to heating element and 1 hex screw on side of tube that secures element and pulled the element out with pliers it comes out a little hard and then slid new element in and put it back together easy fix

No heat but dryer runs other wise

  • Customer: Donald from Burlington CT
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
there were 5 ,1/4 screws in the back panel . The heater box was right at the rear when the back was removed.. Replaced the two controls that were in the kit with a 1/4 nut driver. Checked the terminals for tightness and contact. No discoloration on contacts. Ran unit after reassembly for 20 min cycle to test ,Put into service

No Heat

  • Customer: Tak from Richmond Hill NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
replace the burnt fuse.
All Instructions for the 11062064100
376-390 of 409