Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 11062062100 > Instructions

11062062100 Kenmore Dryer - Instructions

All installation instructions for 11062062100 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11062062100
361-375 of 421
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

door catch broke off

  • Customer: barbara from san diego, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
just the way the video showd me

The dryer would run but with no heat.

  • Customer: Robert from Riverview, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Disconnect power source first. I used a butter knife in the absence of a putty knife to pop open the spring hinges on the front access panel. I then removed the panel off of the bottom hinges. I then took a socket wrench and disconnected the bottom part of the support that holds the dryer element. Turn the dryer this unit about a quarter turn and remove bring the unit toward you. I then took a picture of the wiring and also took a non-black marker and marked one spot on the wires that were connected to the first clips and wrote down what color was on top. I then disconnected them and went to the second clips Two spots with the marker and recorded which wire was on top. Then the same with the third set of clips 3 spots. Once all the wires were disconnected I then removed the unit and simply replaced the thermostats and then put everything back in reverse order. I never had to refer to the camera phone but it was nice to know that it was there. The video provided by this web site was very helpful and gave me the confidence to tackle this and saved me a bunch of money. Thanks guys.

The dryer stopped working during an electrical storm. The display showed "PF". Dryer would not turn on after cancel switch was activated.

  • Customer: Christopher from Sugar Land, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
After shutting off the gas supply and unplugging the electrical cord, I used a flat blade screwdriver to loosen the exhaust vent clamp and remove the vent tube from the outlet. Using a 1/4-inch nut driver I removed the screw holding the plate covering the electrical lead connection to the power supply, then I pulled the plate back and disengaged the tab from the cutout in the back of the dryer body to remove it. I then removed the eight screws holding the back cover of the dryer in place, then removed the cover. The thermal fuse is located near the bottom of the dryer at the back, just above the exhaust vent. I loosened the two screws holding it in place using the 1/4-inch nut driver, then I removed the two electrical leads from the fuse. I inserted the new thermal fuse and screwed it into place, then reinstalled the electrical leads. I then reinstalled the back cover, the power-cord cover, and the vent hose. I turned the gas supply back on and plugged the electrical cord back in.

door would not activate dryer......lever broke!

  • Customer: nancy from troy, MT
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I am one Happy Gal.....Looked to fix,thought about just buying a new dryer..In the end talked to the local repair guy...said I could do it myself. (why pay him)..I live in small town.Ordered your part,watched the video and did it...Saved myself over $500, plus the $125 for delivery.for that new dryer..(Small town in the forest!)Very easy to install....Hope to use this dryer for many months perhaps years..It is 30 years old! Works like a champ! Thank You!

No heat from element

  • Customer: Don from Chaffee, MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
More time troubleshooting than repairing. Used online help for narrowing down problem to the thermal cut-off unit. Had to remove front lower cover, remove wire sets from heating element,remove element from dryer. Then it was a simple swap out of the two relays/thermistors, and put it all back together again. Unit worked as designed after repair.

Dryer wouldn,t heat.

  • Customer: Keith from Rancho Murieta, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
Removed the bottom front panel. The difficulty was in locating and testing the components because of access. Removing the heater required removing the heat shield and bracket and restraining screws, and then pulling out the heater with pliers which was stuck because of age. Dryer now works fine.

The grill cover to the dryer vent broke in half

  • Customer: Linda from Fort Myers, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I ordered the part with the manf. # BUT upon installation I found that the new part was slightly different than the old part therefore not allowing me to screw the new part to the inside of the dryer - I was able to find longer screws that would work but took me an hour to figure out what the issue was and then resolve the matter

Dryer would stop heating. Would reset after several hours and work again.

  • Customer: Stephen from Ballwin, MO
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I knew I needed a thermostat. So that part of the repair was my contribution.

Dryer don't heat

  • Customer: Ali from Brecksville, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
As described by the video, I removed the front cover after I unpluged the electric plug. Pulled all the wires from the cutoff-TML. Removed the cover of the heating element(one screw). Removed the heating element housing(2 screws). Removed the cutoff-TML from the heating element housing(2 parts, 4 screws). Replaced the cutoff-TML(3screws). Returning the heating element housing to its place was somewhat difficult, it took few tries.Then reattached the wires on the new cutoff-TML.Returned the cover of the heating element. I pluged the electrical plug. Turned the dryer on high for 3 minuts and watched the heating element getting hot. At last I returend the front cover.

no heat

  • Customer: WILLIAM from BALTIMORE, MD
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
after using a meter to determine the thermal cut-off was bad and ordering the part, it only too about ten to fifteen minutes to repair. used a nut driver to remove the bag cover to expose the thermal cut-off. removed the wires and the screws from the parts. screwed the new parts on. replaced the wires. turned the dryer on to make sure it worked (heat came out). replaced the cover. set back in place and it works great

replaced lent filter

  • Customer: BILL from LANCASTER, SC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
replaced the lent filter

no heat in dryer

  • Customer: Lynn from Huntsville, AL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
diognostic suggested thermal fuse or thermistor. Thermistor tested low resistance (<2K olms). Replaced thermistor and dryer heat returned.

Felt falling off of lint trap filter

  • Customer: Kimberly from Broomfield, CO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Took the old one out and replaced with new filter.

Dryer door wouldn't stay closed

  • Customer: LaToya from Medford, NY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I didn't have to remove the entire door...I just removed the screws with the door open, used a needle nose plier to remove the plastic insert..stuck the new one in. Then I replaced the metal portion by popping it out and inserting the new one. Easy

The door would pop open and the catch was broken

  • Customer: Janice from Syracuse, IN
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
When I got the door catch, I held it in a pair of pliers and pushed it right into place. The door would still pop open. After awhile, I realized that the door was bent, probably by a small child climbing up on it. I had to loosen some of the screws that held the door on in order to relieve the tension in the door so that it would stay closed. As long as it continues to work, I won't worry about replacing the door. It's in a rental house anyway.
All Instructions for the 11062062100
361-375 of 421