Models > 11062052100 > Instructions

11062052100 Kenmore Dryer - Instructions

All installation instructions for 11062052100 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11062052100
1-15 of 388
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Door Catch part had fallen out,/ was missing

  • Customer: Terri from Saint Augustine FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 478 of 481 people found this instruction helpful
Received your parts, Popped them both right into place, Even though only one side needed to be replaced, I wanted them to match up. It was amazing how easy this was. My husband was quite impressed I had ordered these rather then look for either a new or used dryer from some other source.

Burned out heater element

  • Customer: Alan from Brooksville FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 209 of 230 people found this instruction helpful
Remove the kick plate from the bottom of the dryer by sliding a putty knife along the top edge to release the plastic clamps, one on each side about 4" in from the edges. The kick plate folds out and down. You will see the heat shield on the right, held in by one hex head screw. Remove screw and heat shield. The element is positioned in an open-front housing and is fastened to the left side of the housing by two hex head screws, located on the "rail" of the element and right near the two wires. Remove the hex-head screws that hold the element in place and disconnected the two wires by pulling them out by hand or with needle nose pliers. The only difficulty here is the cramped working area...I recommend a stubby socket driver for these two screws. Most of this I had to do by feel because I could not see the screw heads. Once the screws are out and the wires have been disconnected, slide the old element straight out toward you. You may need to disconnect a small plastic hose located to the left front of the element, but this hose just pulls right off. Vacume the dust & lint build-up out of the whole area, wipe out the element housing and clean up the whole underside of the dryer prior to installing the new element. Installation is reverse of removal. It also might be a good opportunity to clean out your exhaust duct and the vent to the outside. (Never use the aluminum foil-accordian-type duct.) If the exterior dryer vent has any kind of screen over it, remove it and get rid of it. Screens collect lint, lint builds up and burns out elements.

Dryer not heating

  • Customer: Wesley from Boyds MD
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 122 of 140 people found this instruction helpful
Our dryer is 8 years old and had been slowly taking longer and longer to dry clothes, to the point that I was ready to purchase a new one. When the dryer stopped heating completely, I removed the bottom panel and found that the heating element was no longer working. I checked online and found this website. The top two recommended fixes for this issue was to replace the heating element and/or thermal cut-off kit (two sensors). I chose to purchase both, delivered to me very quickly (two days). I figured for $80 you can't go wrong. Here's the procedure I followed:

On my particular model, the back does NOT come off and all of my repairs had to be made via the front, bottom panel.

(1) disconnected 6 wires (3 pairs) from the heating element and two thermal sensors
(2) removed entire heating element 'sleeve" which contained both the heating element AND the two sensors. The space is way too tight to try and do this any other way (and I highly recommend this method to save a ton of time and frustration.)
(3) vaccummed out the entire inside of the dryer, clearing all lint and debris, including tons of lint creating a blockage, thus slowing the ability to dry over the years
(4) replaced sensors and heating element
(5) installed heating element & Thermal sensors back inside and reconnected all wires
(6) tested dryer to ensure that heating element lit up and produced heat - it worked beautifully!

Besides fixing the heating issue, cleaning out the clogged lint pipe at the back of the dryer and wall have made the old dryer new again. It's working better than ever!

Door wouldn't latch.

  • Customer: Melody from North Las Vegas NV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 147 of 218 people found this instruction helpful
I can't believe I waited so long to find this part and do this. I got the package very fast, opened it, took the piece to my dryer and popped it into place with my fingers. It worked perfectly! this took all of two minutes and saved me from having to hold the dryer door closed with a stick. Thank you, thank you!!!

dryer door would not stay shut

  • Customer: Pam from Woodbridge VA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 72 of 72 people found this instruction helpful
This repair was a cinch. Pliers to pull out the metal piece and a screwdriver to pry out the 'catch' part in the door. Both replacement pieces went right in. I cannot believe how easy and CHEAP this fix was, and I'm so glad I found this site!! I figured I would have to call a repairman and pay big bucks, so I put it off, but the door was getting worse--slamming it so hard to keep it shut. Again, thanks for this great site.

felt strip came off lint screen

  • Customer: JEFFREY from FALL RIVER MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 81 of 103 people found this instruction helpful
ordered new lint screen, removed old screen, inserted new screen.

door kept coming open dryer shuts off

  • Customer: RONALD from SALMON ID
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 80 of 143 people found this instruction helpful
use screwdriver topry plastic out plyers to pull out metal latch put new parts in

door switch actuator spring broken

  • Customer: Paul from Vero Beach FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 49 of 55 people found this instruction helpful
-unplugged appliance
-removed lint trap
-removed 2 lint trap shute screws with phillips screwdriver
-popped open top of appliance with standard screwdriver by applying pressure at each front corner so that it could be tilted up to access actuator switch on right side of door
-removed 2 actuator switch screws, located on upper right side of laundry door, with phillips screwdriver (screws are accessed from outside of door frame not through appliance top).
-discarded broken actuator spring (accessed from open appliance top)
-replaced new actuator spring
-replaced 2 actuator switch screws
-closed top
-replaced 2 lint trap shute screws
-replaced lint trap
-plugged in appliance
-tested for operation
-kissed by happy wife

Door won't latch

  • Customer: Jill from bellevue WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 74 of 132 people found this instruction helpful
I did NOT have to repair the latch on the actual door, just the small metal piece that it hooks on (on the dryer itself) and it took about 10 seconds to.....do it myself. Just used needle nose pliers so squeeze the piece together and fit it in. thanks

dryer wouldn't dry

  • Customer: JEFFERY from ABINGDON VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 75 of 146 people found this instruction helpful
un pluged it then removed the hose took the back off took out the 2 screws out of each part replace it with the new parts , then pluged it back to make sure it would work and it did the very first time. i'm 1 happy roper owner.

Drum of the dryer was rotating but no heating

  • Customer: Tomasz from University Heights OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 32 of 36 people found this instruction helpful
First I removed the back cover (several screws). Then, I disconected wires from the high-limit thermostat and the thermal cut-off fuse (both of these parts were included in the Thermal Cut-Off Kit). Then, I removed four screws that hold these two parts, replaced the parts, put the screws back, and attached the wires. Finally, I put back the cover.

Dryer wouldn't turn on

  • Customer: Olive from Williamsburg OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 30 of 41 people found this instruction helpful
Removed the back of the dryer taking off the screws. Found the disposable thermal fuse. Unplugged the 2 blue wires connected to it. Removed the screws holding the part in. Replaced the old part. Reattached the blue wires. Put the back on the dryer. And voila! That simple!
I'm a 39 year old woman with absolutely no patience for tedious jobs, but this was so easy I felt good about doing it. And felt even better for saving lots of money by doing the repair myself.

Our dryer started squealing and would then stop running.

  • Customer: Kelly from Aptos CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Wrench(Adjustable)
  • 27 of 33 people found this instruction helpful
After determining that the dryer motor was the issue I wrote down the part number and logged on to partselect.com.

I input the number into the search box and there was the exact motor I needed.

The price was fair and the delivery quick so I figured I would give yuo guys a shot and see how it goes.

The part showed up on time and as expected. It was well packed and most importantly - it was the CORRECT part.

I disassembled the dryer which involved removing the lint trap, pulling out the blower fan and removing the motor cover. The motor was held in with 2 metal screws and wiring harness.

I took the belt off of the tensioner and pulled out the old motor. The motor was mounted with 2 clips which snapped off with ease. Reassembly was a breeze since the motor fit perfectly- the entire transplant operation took all of about 35 minutes.

I crossed my fingers, turned on the gas, plugged it in and........SUCCESS!

Since the dryer was down for over a week the backlog of laundry was piled pretty high. This replacement motor would immediately be put to the test.

It has been 5 days of non-stop drying and no squeeks, no squeels and nothing but dry clothes!

Thanks to Part Select for getting everything right the first time. It made a potentially very bad experience turn out as good as I could have ever hoped.

Felt gasket on lint filter loose...

  • Customer: Catherine from Atascadero CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 25 of 28 people found this instruction helpful
Found this site by googling, and it works! I searched lint filters and just ordered based on how it looked...LOL! Husband wasn't home, it looked pretty much like the one I had in my hand, so.... I ordered it. It is the perfect fit and seems to have a tighter gasket glued in all around the screen. Let's hope this one lasts longer than 6 months! Thank you Parts Select for being so fast!! Filter got here in less than 48 hrs.!

Dryer would not heat at all.

  • Customer: Lou from Orlando FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 20 of 22 people found this instruction helpful
Found a service manual on-line for the Whirlpool Duet Dryer. Did the troubleshooting for the problem stated. Found the heater element to be bad (open circuit across heater block). Ordered new element from PartSelect.com and installed. Dryer now works like a charm and I didn't have to call a repairman.
All Instructions for the 11062052100
1-15 of 388