11061812000 Kenmore Dryer - Instructions

Removed and replaced terminal block, power cord and black wire to timer.

My wife was doing a load of laundry when she thought the the dry cycle was finished she found the cloths still wet. When she went to restart the dryer nothing. I did some research online and found the most common problem was the thermal fuse. I removed the back of the dryer removed the fuse and checked for continuity with my volt meter. I thought that I was going to find alot of lint build up. However I did not so I decieded to also replace the thermostat, using the thermo cut-off kit because this might have caused the fuse to fail. I ordered the parts from partselect and they arrived in two days. Partselect has excellent instructional videos on how to make the repair. It was quick and easy and saved the money of just going out and buying a new appliance.

I bought a belt from a store in my area- What a mistake...I found this site and read all the stories on how easy it was and how PartSelect.com had the parts in stock and had easy instructions...I put the idler pulley in place, put the belt in place (all from instructions included) and put the dryer back together (which was easy). I actually did it alone. I would recommend this company to anyone in need of their parts and help!

i decided to order the new element which was the most expensive part then decided to add the thermostats just incase they were bad because they were rather inexpensive. got the parts in took the back off the dryer located the parts i ordered and simply replaced them with the power cut off to the unit. put the back on and it heated like it was better that new my clothes dry 5 times faster than it did when i bought the thing.

Lint filter supplied by Parts Select was an exact replacement by an aftermarket manufacturer. I put the old one and the new one side by side and they were identical (of course, the handle wasn't broken off on the new one!). I coulnd't be happier. It arrived at my house 2 days after I ordered it. I highly recommend Parts Select.

Remove back cover
Raise top
Remove filter assembly
Remove front cover and drum

Tip: Use an end wrench on the fan and another on the pully shaft of the motor to remove fan from motor prior to removing motor from cradle.

Vacuum everything while disassembled

Remember to take your time and not force anything and this will go smooth.

First of all, you go in from the front. There a clip on each side that I just pried up to pop the front of the dryer up. A screw also needs to be removed in the lint catcher area. Also, two screws holding the door open switch must be removed as I never could get the electrical connectors to disconnect. No big deal. I had to figure out you must lift the front of the dryer up as the last two things holding it in are a prong on each side. Lift the front up and off and set it aside. As you do this the drum will either fall on your feet or you'll have it supported be another person or with something else. I used bungee cords and kept it in the laundry room. Cleaned out all the old lint, collected a few bucks in change. It took me awhile to figure out how the new belt routed through the removable pulley guide thing and around the wheel pulley. I don't remember right now as I'm not looking at it but remember pinching the belt and feeding it through the guide and around the wheel pulley which has a little slot and grooves matching the belt. Besides scrapping my wife's hand while she was helping me get the front of the dryer back on there were no casualties or further complications. Good luck!

I removed the discharge duct from the back of the dryer. Then, I removed the screws on the back of the dryer and the back itself. This exposed the cycling thermostat. I removed the screw holding the thermostat. I took the wires off the defective thermostat and reinstalled them on the new thermostat. Then, I reassembled in reverse order.

I wasn't sure if I was going to be able to do the repair myself. Happily, I was able to and my dryer works like new ! I figure I probably saved about a 100 bucks doing it myself rather than calling out a repair man. Oh, did I mention I am female and didn't have to have a man do this for me. :)

I took a ¼ inch nut driver and removed the rear cover from the unit, and then used a continuity tester to determine which safety device was open. According to the schematic there was one non-resettable safety device in the heating circuit, and that was open. The kit that I ordered came with thermal cutoff and a thermostat. I replaced both parts and the unit now operates normally. While I had the dryer open I thoroughly cleaned the dust and lint from the unit and also the 4 inch vent pipe. I ordered this part on Friday morning and received it early Saturday afternoon.

Following the instructions that came with the parts, I removed the top off of the dryer, which was very easy, two more 5/16" screws and I had the drum out. I confess, this was my second time at this repair. 1st time I neglected to replace the rear drum seal which I strongly recommend you do while you have it open. I only replaced the 2 wheels last time and it failed very soon afterwards.
Lesson Learned: Always replace the rear drum seal when you replace the support wheels!!!

Disconnected supply. Lifted top (hinges on rear). removed two 1/4 hex head screws retaining front panel. Disconnected door switch wires. Removed front panel, lifting off from bottom tabs. Lifted out drum and discarded broken belt. Spent 30 minutes+ cleaning interior, drum skid area, dryer exit tube, motor pulley, belt tensioner, etc, etc. Checked wiring harness for possible damage (no damage found). Repositioned drum skid pads, which had become dislodged from their intended position. Reinstalled the drum with new belt, ensuring both belt & tensioner were correctly positioned, and drum rollers and felt seals were also correctly positioned. Reinstalled front panel, tightening the two 1/4 hex head retaining screws. Reconnected power. Checked functionality. Closed top cover.

I removed the four screws holding the
heating element, then I pulled the element out
and then put the new element in and hucked
the wires from the old element after I disconnected
them to the new element..no problem......

The old catch on my dryer door was gone and I was keeping the door closed using tape. I ordered the part and it arrived with no hassles in about 5 days. The repair was too easy. I just popped the new catch in place. It took all of about 30 seconds to complete using no tools. I wish all home repairs were this easy.

First, remove the back panel of dryer which is about 10 screws. Then remove the 2 thermal switches, one is above the heating element and the other is where the hot air comes out. They are both really easy to get to and the pictures on Part Select.com are identical, so you can order the part first and then just "match them up" if you are not sure what to replace. Oops, the first step is to unplug the dryer.