Models > 11061252011 > Instructions

11061252011 Kenmore Dryer - Instructions

All installation instructions for 11061252011 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11061252011
1,201-1,215 of 1,267
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Very loud

  • Customer: Bradley from Mineral Point MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Had to order idler lever and wheel as the one in the kit would not work. Best to buy part specific for your dryer. Repair was easy, just watch repair video. Sounds like new dryer again

noise due to worn drum wheels

  • Customer: Derek from Wyoming MI
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
flipped top up, removed 2 5/16 screws and removed front face. removed drum and belt. removed retaining clips on rollers and removed wheels. replaced all clips and new wheels and installed new belt on drum and reassembled in reverse order

dryer turned on but would not spin

  • Customer: JAMES from DUGGER IN
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Watched video on You Tube, ordered parts online and used excellent instructions sent with belt and other parts in kit. Turn power off by unplugging cord, lift out lint screen, remove screws in lint screen slot, pry up top of dryer with wood chisel or heavy screwdriver, unplug wires top front of dryer, remove self-tapping screws holding front panel in place, lift out drum, remove and replace all parts included in kit, lifted drum back into place, placed detergent bottle under drum to hold it in place while attaching new belt, asked wife to hold lightweight drum in place while I reattached electrical wires and front of dryer. Lowered top of dryer into place and reinstalled lint screen, Be careful! Panels are thin and cut like a knife. Also the dryer lid can fall if you slide the dryer into the wall while working below.

Broken drum belt

  • Customer: Charles from Peachtree City GA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Follow the instructions contained in the kit along with the excellent referenced how to video on YouTube. Will certainly go to PartSelect for all my future appliance repairs.

Dryer was getting hot but clothes not drying........

  • Customer: Camille from North Providence RI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
It was a shot in the dark given I've never performed any trouble-shooting on a dryer before but it was either I try or spend $900 - that I don't have - for a new dryer. I'm female, very mechanically inclined, and will try anything once. My previous recent parts order from PartSelect.com proved successful (in-wall oven door hinges and gasket) so I decided to at least try. To have a repair person come in the house would be at least $100 and that wouldn't cover parts; I don't know anyone to call so that made it worse. And again, buying a new dryer was even worse. I did an Internet Search on my dryer model and also put in "gets hot but won't dry". I received answers that it most likely was a belt. Logic told me - before the search - that a dryer must have either a pulley or a belt to operate so I thought I was on the right track! Lo and behold up pops up Partselect.com as having a belt which the website stated was about 85% the cause of my problem. The belt was $11.49 - how could I go wrong to just try it!??? I then found positively OUTSTANDING VIDEOS on how to change the belt and one thing led to another and I decided to purchase the entire repair kit (wheels, belt, etc.). I also decided to change the thermal fuse given the age of the dryer and while it did get hot it seemed to take a long time for a small amount of clothes. Purchased the kit and fuse, had them shipped 2-day priority (total cost $60) and downloaded the videos to change the entire kit and the fuse after having watched them on the website. I brought my laptop down to the washer/dryer area and place it on the washer. Turned on the video and followed it - stopping the video to perform my part of the repairs. It worked FANTASTIC!! One thing I did find was the dryer had never been serviced and was positively loaded with dust, dirt, "kitties", the lint chute had never been cleaned out and it had toothpicks, nails and screws in it. The entire project took me over 4 hours but that was only because the inside of the dryer was sooooooooo disgustingly dirty. I vacuumed everything - even the motor was covered with caked on dust - and when it came time to install the new parts I breezed right through their installation. There were even written instructions with the parts along with written instructions on the Partselect.com website but the videos are AMAZING! They made this repair so easy to perform, everything was laid out on the video and once I had the "squeaky clean" dryer all put back together I flipped the switch to find it worked like a brand new dryer! I have saved $840 (not counting taxes and delivery fees for a new dryer) and I have now completed TWO major appliance repairs myself........no outside or professional help ..........and I owe it all to Partselect.com and the super videos and parts that FIT! If you need a part look HERE FIRST; if you need help in the repair job: LOOK HERE FIRST. I've never been so happy about a repair as I am the dryer and not only for the tremendous amount of money spent but the ease in which Partselect.com made it with the videos. My mother is thrilled with her "new dryer" and I honestly can't believe it was so easy to repair!! THANK YOU, PARTSELECT.COM!!!

drum not rotating

  • Customer: Robert G from Dansville NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Pull lint screen, remove two phillips screws,pry top front up and hinge back,remove two screws at top inside, unplug door switch, lift front and remove, remove drum. Read instructions,install new parts, reverse above dis-assembly, happy dying.

broken belt and roller

  • Customer: FLOR from Jersey City NJ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 0 of 0 people found this instruction helpful
Replaced Broken Belt and roller

Squeaking noise and stopping during drying cycle

  • Customer: David from Thomasville NC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced the Drum Roller, Belt, Belt Tensioner and Rear Drum Seal by watching the video that was attached with the order form from PartSelect. Removed screws from lint filter, raised the top by sliding it forward a small amount, able to raise top and leaned it against a wall. Then removed two screws from front panel and lifted front up slightly while holding the drum and removed it from front of dryer and placed it out of the way. Loosened the tensioner pulley to remove the belt and once that was done pulled the drum out and replaced the drum rollers (by looking at the video). The rear drum seal was the most aggravating part in getting it off and cleaning it up. Was a little messy putting it back on and then just reversed everything to put it back together. It is working properly now. Thanks to the video. PartSelect parts came earlier than I expected they would and I appreciated that very much.

Broken Dryer Belt

  • Customer: WILLIAM from DELRAY BEACH FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Ordered entire Maintenance kit - good call because it was the tensioner pulley that failed and cut the belt. To replace, had to raise the top (2 screws in lint screen slot)and pull the entire front off (2 screws - 1/ea on top inner edge of front door panel then lift it up and out) Replaced both rollers, then used the parts kit shipping box to prop up the front of the drum while installing the belt and tensioner pully. Re-assembled in reverse order, works fine.

Installation of Maintence Kit & Door Latch

  • Customer: Roger from Twinsburg OH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Parts were received in one day!!!The instructions were clear, concise and easy to follow. The pictures and figures significantly added to the ease of completing this task.

Load whinning sound

  • Customer: Gary from Pasadena TX
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I reviewed the instruction video. Excellant video. exactly like my dryer. Just followed the instructions. I did put a shoe under the drum for easier installation of belt onto idler pulley. I vacuumed and cleaned inside. Really not that dirty.Excellant web site and video instructions. Wish I had done the repair sooner. Also God Bless the residents of OK city, Moore, and ElReno.

drumbelt broken

  • Customer: David from N Chelmsford MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Used a ropeasround the dyer drum to simulate thebelt to peload the idler This allowed me to get the belt over the motor shaft without the idler sping tenion causing the idler to jump at random timesafer I strted using the rope the belt was on in 10 minutes.

Noise coming from the dryer

  • Customer: Kevin from Grafton MA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
After watching your video, and reviewing the directions, I was able to change the rollers, the belt and tension bar with ease. The parts cost me slightly under 50.00 and now the noise is gone and my dryer works great. I am very pleased with PARTSELECT and would use them again. The parts were at my house within three days of placing the order !!!

Dryer stopped spinning, but still putting out heat

  • Customer: Janice from Winston Salem NC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Basically, I just did everything in the Parts Select video - it's what gave me the courage to attempt the repair myself and I am a 61 yr. old woman, who's not in great physical shape! The belt had broken. The two things that gave me the most trouble were disconnecting the tab on the door switch assembly and getting the screws to line up when replacing the front panel - one side lined up fine - the other needed a good push and an "alley-oop" to the side with my hip to fall into place. I did a few things that were not in the video which I think really helped me out. (1) I put an empty quart sized paint can under the dryer drum to hold it up - that really helped - I only had to support it slightly myself when threading the new belt. (2) I put a piece of duct tape across the bottom of the idler pulley to keep that from falling out of the holes when I was threading the new belt - that worked like a charm. Just be sure to remove the piece of duct tape and the paint can before you close up the dryer, if you decide to follow those two tips. (3) I also eventually put something under the front door panel to help raise it up and get it more in line with the two holes that it connects into, which made it easier for me to get it back into place. (4) Have some bandaids on hand - I sliced two fingers on different parts while installing the whole kit. (5) After you are done, either clean out the dryer vent hose or put a new one in - I was surprised by how much lint was clogged up in there. I never repaired any appliance before and if a 61 yr. old weakling like myself can do it, anyone can. Parts Select Rocks - the kit arrived a day and a half after it was shipped out and the video tells you everything you need to know to do this repair yourself and save big money. $49 versus probably $150 for a repairman and $500+ for a new dryer. Dryer is running like new! Would definitely do this again, if this or another dryer broke in the future. Thanks!

Noise while drom turning on heavy loads

  • Customer: John from Farmington Hills MI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
Found the perfect maintenance kit and helpful repair video on PartSelect.com. Factory replacement parts were delivered quickly along with written installation instructions.Never needed them. Just performed the repair while watching the step by step video. Dryer works great, no noise. A very happy customer.
All Instructions for the 11061252011
1,201-1,215 of 1,267