Models > 11061086000 > Instructions

11061086000 Kenmore Dryer - Instructions

All installation instructions for 11061086000 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11061086000
1-15 of 319
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Door Catch part had fallen out,/ was missing

  • Customer: Terri from Saint Augustine FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 478 of 481 people found this instruction helpful
Received your parts, Popped them both right into place, Even though only one side needed to be replaced, I wanted them to match up. It was amazing how easy this was. My husband was quite impressed I had ordered these rather then look for either a new or used dryer from some other source.

Burned out heater element

  • Customer: Alan from Brooksville FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 209 of 230 people found this instruction helpful
Remove the kick plate from the bottom of the dryer by sliding a putty knife along the top edge to release the plastic clamps, one on each side about 4" in from the edges. The kick plate folds out and down. You will see the heat shield on the right, held in by one hex head screw. Remove screw and heat shield. The element is positioned in an open-front housing and is fastened to the left side of the housing by two hex head screws, located on the "rail" of the element and right near the two wires. Remove the hex-head screws that hold the element in place and disconnected the two wires by pulling them out by hand or with needle nose pliers. The only difficulty here is the cramped working area...I recommend a stubby socket driver for these two screws. Most of this I had to do by feel because I could not see the screw heads. Once the screws are out and the wires have been disconnected, slide the old element straight out toward you. You may need to disconnect a small plastic hose located to the left front of the element, but this hose just pulls right off. Vacume the dust & lint build-up out of the whole area, wipe out the element housing and clean up the whole underside of the dryer prior to installing the new element. Installation is reverse of removal. It also might be a good opportunity to clean out your exhaust duct and the vent to the outside. (Never use the aluminum foil-accordian-type duct.) If the exterior dryer vent has any kind of screen over it, remove it and get rid of it. Screens collect lint, lint builds up and burns out elements.

Door wouldn't latch.

  • Customer: Melody from North Las Vegas NV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 147 of 218 people found this instruction helpful
I can't believe I waited so long to find this part and do this. I got the package very fast, opened it, took the piece to my dryer and popped it into place with my fingers. It worked perfectly! this took all of two minutes and saved me from having to hold the dryer door closed with a stick. Thank you, thank you!!!

dryer door would not stay shut

  • Customer: Pam from Woodbridge VA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 72 of 72 people found this instruction helpful
This repair was a cinch. Pliers to pull out the metal piece and a screwdriver to pry out the 'catch' part in the door. Both replacement pieces went right in. I cannot believe how easy and CHEAP this fix was, and I'm so glad I found this site!! I figured I would have to call a repairman and pay big bucks, so I put it off, but the door was getting worse--slamming it so hard to keep it shut. Again, thanks for this great site.

felt strip came off lint screen

  • Customer: JEFFREY from FALL RIVER MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 81 of 103 people found this instruction helpful
ordered new lint screen, removed old screen, inserted new screen.

door kept coming open dryer shuts off

  • Customer: RONALD from SALMON ID
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 80 of 143 people found this instruction helpful
use screwdriver topry plastic out plyers to pull out metal latch put new parts in

door switch actuator spring broken

  • Customer: Paul from Vero Beach FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 49 of 55 people found this instruction helpful
-unplugged appliance
-removed lint trap
-removed 2 lint trap shute screws with phillips screwdriver
-popped open top of appliance with standard screwdriver by applying pressure at each front corner so that it could be tilted up to access actuator switch on right side of door
-removed 2 actuator switch screws, located on upper right side of laundry door, with phillips screwdriver (screws are accessed from outside of door frame not through appliance top).
-discarded broken actuator spring (accessed from open appliance top)
-replaced new actuator spring
-replaced 2 actuator switch screws
-closed top
-replaced 2 lint trap shute screws
-replaced lint trap
-plugged in appliance
-tested for operation
-kissed by happy wife

Door won't latch

  • Customer: Jill from bellevue WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 74 of 132 people found this instruction helpful
I did NOT have to repair the latch on the actual door, just the small metal piece that it hooks on (on the dryer itself) and it took about 10 seconds to.....do it myself. Just used needle nose pliers so squeeze the piece together and fit it in. thanks

dryer wouldn't dry

  • Customer: JEFFERY from ABINGDON VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 75 of 146 people found this instruction helpful
un pluged it then removed the hose took the back off took out the 2 screws out of each part replace it with the new parts , then pluged it back to make sure it would work and it did the very first time. i'm 1 happy roper owner.

Dryer wouldn't turn on

  • Customer: Olive from Williamsburg OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 30 of 41 people found this instruction helpful
Removed the back of the dryer taking off the screws. Found the disposable thermal fuse. Unplugged the 2 blue wires connected to it. Removed the screws holding the part in. Replaced the old part. Reattached the blue wires. Put the back on the dryer. And voila! That simple!
I'm a 39 year old woman with absolutely no patience for tedious jobs, but this was so easy I felt good about doing it. And felt even better for saving lots of money by doing the repair myself.

Our dryer started squealing and would then stop running.

  • Customer: Kelly from Aptos CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Wrench(Adjustable)
  • 27 of 33 people found this instruction helpful
After determining that the dryer motor was the issue I wrote down the part number and logged on to partselect.com.

I input the number into the search box and there was the exact motor I needed.

The price was fair and the delivery quick so I figured I would give yuo guys a shot and see how it goes.

The part showed up on time and as expected. It was well packed and most importantly - it was the CORRECT part.

I disassembled the dryer which involved removing the lint trap, pulling out the blower fan and removing the motor cover. The motor was held in with 2 metal screws and wiring harness.

I took the belt off of the tensioner and pulled out the old motor. The motor was mounted with 2 clips which snapped off with ease. Reassembly was a breeze since the motor fit perfectly- the entire transplant operation took all of about 35 minutes.

I crossed my fingers, turned on the gas, plugged it in and........SUCCESS!

Since the dryer was down for over a week the backlog of laundry was piled pretty high. This replacement motor would immediately be put to the test.

It has been 5 days of non-stop drying and no squeeks, no squeels and nothing but dry clothes!

Thanks to Part Select for getting everything right the first time. It made a potentially very bad experience turn out as good as I could have ever hoped.

Felt gasket on lint filter loose...

  • Customer: Catherine from Atascadero CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 25 of 28 people found this instruction helpful
Found this site by googling, and it works! I searched lint filters and just ordered based on how it looked...LOL! Husband wasn't home, it looked pretty much like the one I had in my hand, so.... I ordered it. It is the perfect fit and seems to have a tighter gasket glued in all around the screen. Let's hope this one lasts longer than 6 months! Thank you Parts Select for being so fast!! Filter got here in less than 48 hrs.!

Clothes would not Dry

  • Customer: Vince from Kathleen GA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 27 of 38 people found this instruction helpful
I simply removed the back of the dryer to gain access to the heating element. Once I removed the heating element I figured I would also replace the thermostat and thermal fuse as preventive maintenance.

Dryer would not heat at all.

  • Customer: Lou from Orlando FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 20 of 22 people found this instruction helpful
Found a service manual on-line for the Whirlpool Duet Dryer. Did the troubleshooting for the problem stated. Found the heater element to be bad (open circuit across heater block). Ordered new element from PartSelect.com and installed. Dryer now works like a charm and I didn't have to call a repairman.

Rear tub seal failure

  • Customer: Jerry from Everett WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 22 of 33 people found this instruction helpful
I removed the top cover and then the back cover, released the belt tensioner and removed the drive belt. Then slid the tub out of the unit and onto the back dack. Sanded the remnents of the old seal off. Wiped the tub lip with laquer thinner and applied the "fast" drying glue supplied with the kit. Installed the seal and re-assembled the unit...works fine
All Instructions for the 11061086000
1-15 of 319