11061066000 Kenmore Dryer - Instructions

flipped THE BREAKER (very important!). Removed the cover on the bottom of the dryer (2 screws), made easier because dryer is stacked on top of washer. Removed the heater box (3 screws). Thermistor located on top of the blower housing (right side). removed old thermistor (2 screws) and unplugged the wires. Plugged the wires into new thermistor, installed the thermistor, replaced the heater box, then tested the dryer. It seemed to work fine. Replaced the cover. It has worked fine ever since.

Removed the front lower skirt with two 1/4"hex screws. Vaccumed all inner parts exposed. Removed three 1/4" screws holding the blower housing.Memoved the bias thermister again two 1/4" screws. Make sure all inner exaust pipes and rear chimney gas or electric are clean and lint free. Re assemble and test the unit. Install the skirt and make sure the dryer is level Jack, Pa.

Followed instuctions on video accept our appliance was the Duet HT model so we had a glass window to deal with. Just a few more screws to keep track of but otherwise a very easy repair.

ordered new latch. Arrived promptly. Installed in 5 minutes. Actually easied than the video. Thanks

The Door Catch Kit had clear instructions for installation and included multiple replacement catches to fit several different sizes/varieties of dryers. I used a screwdriver to pry out the broken door catch, popped in the replacement, and was done! As usual, PartSelect had what I needed at a good price, with clear instructions for any needed installation. Fast shipping, too.

First I reviewed the diagram to become familiar where items were located. I then insured unit was unpluged I used nutdriver to remove front cover from dryer. Noticed a lot of lint. Good time to vacuum it made finding screws and wires easier.Next Located heating element as described in parts location diagram. Utilized small socket to remove screws in cover plate. the socket set allow easy access to screws under cover plate. Removed 2 electrical wires from heating element. Pull heating element from housing with needle nose pliers. Had to tug a little, inspected element and found break in heating coil.Placed in new element by using reverse installation procedure. (didn't replace lint)This was an easy fix and I saved lots of dollars on repair or hundreds on new dryer. I spent about 20 minutes on the entire project. If you can read you can do this project. Very easy to complete. PS Ordering the parts was easy and arrived earlier than exepected.

This was such an easy repair that my brother (who is a handyman but with no dryer experience) was able to remove the old element and install the new one in about 30 minutes. I was so happy that I found this website and that the part worked on the first try. I think my dryer works better than ever before!!

My Daughter and I have the same washer and dryer from Maytag. Her felt piece came apart on the lint filter. I let my fingers do the walking and checked which filter went with the dryer and purchased it. When it got here, I made sure it matched up with the old one and just put it in the dryer where it belonged.

This was by far so easy the instruction Partselect gave me where right on step by step. a repair man was going to charge 75$ just to come out 9$ from partselect. Thank you very much Mike chaplin

1. Disconnect power cord and remove flexible duct. 2. Tilt dryer back and lean against wall, using folded towel to prevent wall damage. 3. Remove front/bottom panel - 4 screws on front/bottom of dryer. 4. Make alignment marks on internal vent duct where it attaches to vent bottom duct housing. Remove internal vent duct screw (towards front/top of duct) and slide vent duct out back of dryer (duct has to be removed to remove back panel) 5. Remove top panel (4 screws on back/top). 6. Remove AC power terminal block from back panel, disconnecting wire that restricts free movement of terminal block. Remove power cord from terminal block (3 nuts). Remove back panel (many screws). 7. From rear of dryer, gain access to idler pulley spring arm. Carefully note how belt routes around motor pulley and idler pulley (maybe record an image). Release belt from idler pulley. 8. Remove idler pulley triangle retainer (if still on pulley shaft) and remove old pulley. 9. Thoroughly vacuum lint and dust from all areas of dryer, internal duct, flexible duct and duct in wall (as far as possible) while dryer is in disassembled state. 10. Thoroughly clean idler pulley shaft of deposits with cloth. If desired, add very small amount of Park Tools Polylube 1000 to the cleaned shaft. 11. Install new washer, idler pulley and triangle retainer to shaft. 12. Re-route belt around pulley in original orientation. 13. Reassemble rear panel to dryer, terminal block to rear panel, and power cable and internal wire to terminal block. 14. Reassemble top cover to dryer. 15. Insert internal duct back into front vent duct, aligning guide marks, and secure with the one screw. 16. Plug unit in and briefly test, then unplug. 17. Again, tilt dryer against wall and reinstall front/bottom panel and screws. 18. Install flexible duct, plug in power cord and position unit for operation.

I read the instructions on the internet. It told me what to trouble shoot first. The switch on the door then the thermo fuse and after that the thermostat. The off on switch on the door checked ok but the thermo fuse didn't when I followed the instructions on the internet. The thermostat did check ok. When I installed the new thermo fuse the dryer started like always before. I was pretty proud of myself for saving a hundred dollars or more. Thank you for the hlpful instructions.Larry

It snapped right in. Works perfect.

poped off front bottom panel just a couple screws to take loose slid out the heat element saved 172.00 dollers

I took the old filter out and placed the new one in the same spot.

I watched the video and after that made the repair, it was very easy and the video was a really big help. From start to finish it took me no longer than 10 minutes.