Models > 11060884990 > Instructions

11060884990 Kenmore Dryer - Instructions

All installation instructions for 11060884990 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11060884990
1,156-1,170 of 1,210
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer made loud noise, shook across the floor

  • Customer: Miranda from Scottsville VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
By following the repair video available, I took off the top and front panel of my dryer, removed the drum, removed the old drum support rollers, vacuumed out the inside of the dryer (so much lint!), replaced the drum support rollers, and put the dryer back together. Dryer runs like brand new and is very quiet. Repair was extremely easy to do. Got the replacement parts in about 2 business days. PartSelect repair videos make the repair easy too! Lots of satisfaction for a girl to repair her own dryer!

Dryer became really noisy then the drum stopped spinning altogether.

  • Customer: Kilalah from Los Angeles CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
First I removed the lint screen from the top of the machine and then the 2 Phillip head screws that where located under the lint screen door. Next I used a Flathead screwdriver to lift the top of the dryer from the bottom and propped it up against the wall in back of my dryer, next i removed the two screws from the inside front corners of the dryer with a ratchet and the appropriate size socket. I then removed the bottom front panel of the dryer with my Flathead by prying it off at the clips once removed I had access to two screws near the bottom, i loosened them with my ratchet and socket, I pulled out the top of the front panel with the dryer door open as I supported the drum with my free hand. once I removed the front panel I then removed the drum and set it aside. I took this opportunity to vacuum out all the dust from the bottom of the machine and the burner. I then removed the screw from the bottom of the first drum support wheel then i pried the clip off the drum support wheel axle Pulled off a second clip that held the wheel in place then i removed the broken wheel. I removed the back clip which was already cracking i put on the new clip, the new wheel and then the second clip, long story short I replaced the other drum support wheel which was still good but since i had everything apart i went on and replaced it too. I then put the drum belt on the drum, and I positioned the drum in place and put the front panel back on i put the top screws back in then i routed the belt around the tensioner and put it back in place. I rolled the drum all away around while pulling the drum gasket out and placing it in its proper position before i tightened the rest of the screws i plugged the machine in and checked to see if it was working as it should it was so i unplugged the machine and tigthend everything after i put the machine back together i dried a load and while running i went into our bedroom and asked my wife "do you hear that"? She said "no" and asked me what was she supposed to hear. We purchased the dryer used about seven years ago and it never ran as quiet as it does now. Its so quiet you can actually hear a click and then the sound of the burner kicking in.

noise

  • Customer: Martha from Clifton Park NY
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Just as in the video. Sounds like new. Had to feel it to make sure it was running.

Dryer was making lots of noise

  • Customer: clayton from clyde park MT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video on this site and it went exactly as described, fixed it and it sounds like a new dryer. Was going to junk it, glad I didn't!

Not enough heat

  • Customer: Steve from Yadkinville NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Unplugged Dryer. Removed back panel of the dryer. Disconnected and removed the Thermal Cut Off switch and replaced. Disconnected and removed the High Limit Thermostat and replaced. Reinstalled rear panel of the dryer. Plugged in dryer. Operated dryer and checked for heat. Operation was proper and dryer works great.

No heat in dryer

  • Customer: Maureen from Manalapan NJ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
We started with replacing a thermal fuse, went onto heating element & then to replacing the high limit thermostat. The replacements went very easily with your videos, but unfortunately it did not do the job & there is still no heat.

no heat during cycle

  • Customer: Patrick from Ulysses KS
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
My grandson and I wiggled the dryer out of it's tight hole, turned it around and squeezed it back in to make room for the repair job. I followed the easy repair video on your site and removed the housing etc, vacuumed the lint collected over the past 6 years, replaced the heater coil and sensor, and had it back within an hour, with most of the time spent on cleaning lint. Thanks for the video!! This kind of DIY can be fun with the right info. Great bonding-time for generation gap, too. Dryer works like new.

Dryer would not heat up.

  • Customer: John from Quincy CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the repair expert on you tube. Went to my dryer and took out the heating element, inspected it, and found a broken element wire. Ordered a new element and since I was in there I also replaced the high limit thermostat. Parts select made it easy and my dryer works great again. Thank you.

to long drying

  • Customer: wallace from portcharlotte FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
removed back panel. removed wire from old therastat one at a time put on new part re-installed thermastat. Replaced back panel & vent line plugged in better now.

wasn't producing heart

  • Customer: Kayley from puyallup WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Wrench set
  • 0 of 0 people found this instruction helpful
The thermostate and one of the wires were burnt. Ordered a thermostate and re wired the connector to the wire. All I had to do was replace the thermostate and connect the wires to it. Took me probably 15 to do it all :)

Dryer would not dry - no heat

  • Customer: DL from Los Alamos NM
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Using the video that is on your website on what and how to replace broken parts, we followed the same procedure. 1. Found the heating element in the back of the dryer after removing the cover panels. 2. Used a volt-ammeter to determine which part(s) was/were not functioning. 3. Used screwdrivers to disconnect/reconnect wires. 4. Closed panels.

No heat

  • Customer: Paul from Westbrook AL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Parts Go Ppppcame in two days, they took fifteen minutes to install.I followed the pdf.instructions from the web site.Cost of parts was less than a service call.

would no longer heat

  • Customer: Terry from Kaufman TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I went online looked up whirlpool and got the phone number and called them told the person on the phone the model number and Ineeded a heating element Igave credit card information had my part in 2days .put that in and discovered Ialso needed athermostat so Icalled whirlpool back and ordered my thermostat and received it in 2 days put the thermostat in put the back on the dryer and I was back in business didn't get behind waiting on my washing ,,not tomention we were in the process of moving thank you you'll worked with me .Iwould buy another whirlpool product easy to work on a and awesome customer service .

no heat

  • Customer: Roy from Orlando FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
I have replaced the element, the thermal cut off switch. high limit thermostat and thermal fuse. Still no heat.... I am trying to figure out what part next. I could use your help.Roy

No Heat

  • Customer: Mark from Loveland OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I didn't. I was out of town when the part arrived. I talked my 13 year old son through the process over the phone. No difficulties. Wife/mom very happy to have her dryer back.
All Instructions for the 11060884990
1,156-1,170 of 1,210