Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 11060857990 > Instructions

11060857990 Kenmore Dryer - Instructions

All installation instructions for 11060857990 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11060857990
1,411-1,425 of 1,576
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

ice tray was broken

  • Customer: mike from fitchburg, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
This was by far so easy the instruction Partselect gave me where right on step by step. a repair man was going to charge 75$ just to come out 9$ from partselect. Thank you very much Mike chaplin

Washer overflowed

  • Customer: Beth from Valley Springs, CA
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Once I watched a YouTube video showing me how to do the job I ordered the part from you. Am so impressed with your fast shipping and best prices via the Internet. Thank you SO much! The water level switch was easy to install, it ws getting the cover on the washer back on that was hard for me since I am 68 yrs old and have a bad knee. Its why it took me two hours to do what most people could do in 20 minutes.

Unusual noise

  • Customer: Ingrid from Orland Park, IL
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Watched the videos for unusual noise... they are great and saved me time with advice how to open the machine from top and front and install belt on tension wheel. Lower roller bad, replaced both. Opted to also order and replace the belt and rear seal upon inspection. Time spent would have been 30 minutes or less but rear seal replacement requires time to clean off old seal adhesive and glue on new one. Take your time with rear seal replacement it takes longer than I thought but worth it. The labor involved to replace the seal alone would have been more than the dryer cost new. Also- I ordered parts at 2pm std shipping option and got them THE NEXT DAY less than 24 hrs later. May not be typical depending on your location but I was amazed. I have been fixing all my own appliances for years first time customer with Parts Select. Oh and EACH of the 3 parts ordered were 10$ less EACH than my local parts guys. WOW

squeaky dryer and already replaced everything else

  • Customer: Melia from Quincy, FL
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
I watched several Youtube videos for this repair. The best showed a man taking you through every part of replacing the rear felt seal. I used binder clips from my home office and he used clothes pins to keep the seal in place while gluing it and letting it set. To completely finish this repair, it takes over 24 hours to get your dryer ready for drying again. Steps to repair: you need to get to the dryer drum, watch a video on how to do this to include taking off belt, idler pulley. Remove Drum from the dryer. take off all the old felt seal. take out new felt seal and place around the drum, it will be pretty tight. secure the seal by using clothes pins or binder clips all the way around the drum. this will help you keep the seal on the drum and guide you as you use the glue to bind the seal to the drum. Using the adhesive provided with the felt seal, going around the drum, glue down the seal and re-clip it so the glue gets a good grip. let dry of at least 1 hour. Cannot use the dryer for another 24 hours to make sure the glue dries completely and is ready for the heat. I had already replaced the 2 rollers, 2 shafts, belt, idler pulley and start switch and dryer still squeaked. Then I replaced the rear felt seal. NOW I am replacing the bulkhead because it is worn flat in some places and is warped. I am waiting on the part.

Replace Rear Seal on Drum

  • Customer: Elizabeth from Myrtle Beach, SC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
First unplug the unit and move to an area where you will have enough room to pull the drum out. I opened the top by sliding a screwdriver in the top left and right edge and popping the clips to allow the top to lean up and back against the wall. I tried to unclip the harness for the door switch but couldn't get the harness to release and instead took out the two screws holding the door switch in place. This is located on the top right inside the dryer door. Once the switch was off I was able to use the socketdriver to undo the two screws on the inside top left and right to release the front of the dryer by pulling up easily and unhooking the bottom front. I was then able to set the front of the dryer aside and begin removing the belt from the tension wheel and motor. Pay close attention to how the two are connected because it will confuse you putting it back together.The belt feeds through the tension wheel and when you release it the tension wheel is just sitting in place and may pop out of place. Remember which slots it sets back into for when you put the dryer back together. We removed the drum, checked the two rollers to make sure they were in good working order. I removed quite a bit of debris from them. Once the drum was out I pulled off the old seal. Took a piece of sandpaper to rub away any excess old adhesive and began installing the new felt seal. Follow the directions carefully to ensure that the seal is sitting on the edge properly before you begin applying adhesive under the edge. I had someone helping me to install the seal but probably would have needed clamps to hold the seal while working it on. It's not a super tight fit but is fitted and once you start putting it on it easily slips off the other side. A couple clamps would hold it in place if you don't have someone to help. Once the seal is on and you apply the adhesive you begin putting the drum back into place first by slipping the belt back over the drum where it can hang until you are ready to put it back on the motor. You have to make sure the seal isn't folded under the back of the dryer. Again a little tricky but if you gently spin the drum slowly counter clockwise a few times you can work it so it's not folded under. Once you see everything is in place you can reconnect the belt through the tension wheel onto the motor. Check drum again by spinning counter clockwise. Install the front of the dryer back on by setting it into the bottom clips. Put the top screws back in. Re-install the door switch making sure it's back in place with the tab sticking through the hole at the top of the dryer door. Bring the top back down. Close the dryer door and plug it back in and everything should be good to go. It wasn't a difficult job at all and I would probably attempt other repairs now that I've done this one. Beware the adhesive is kind of watery when it comes out but you don't need to use a lot under the edge of the seal. Good luck with your repair. I am thankful that PartSelect was so easy to order my parts from and I got the part within a few days. Thanks!

Drum seal came apart

  • Customer: Glen from El Paso, TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Raised top of dryer and removed screws holing front on. slid front panel up and off to remove drum. Seal was easy to install but you do have to be careful with the adhesive. After adhesive was dry laid dryer on it's back and installed drum. Reinstalled drum belt. Placed front panel back on and installed the two screws holding it in place. Set dryer upright and closed top.

Broken clips

  • Customer: Roger from Twinsburg, AL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Turned off power and pulled power plug from the wall. Removed the two screws at the lint screen. Raised the top to by depressing the top spring clips. Removed the two 5/16" screws from front top. Removed wiring clips from front panel. Set the front aside while I removed the two broken panel clips. Installed the two new panel clips. reinstalled the front panel by placing the front panel above the sides. Opened the front panel door and supported the drum while allowing the front panel to slide down onto the new front panel clips. Reinstalled the wiring clip. reinstalled the two 5/16 screws. Turned the drum to ensure that the felt seals and drive belt weere installed properly. Lowered the top and reinstalled the two screws at lint screen. Reinstalled power plug and turned on power. No rattles or squeeks!!!

dryer would not heat up

  • Customer: Anthony from Leander, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed back panel of the dryer and located the thermal fuse. Disconnected two wires, and removed one screw holding the fuse in place. Installed new fuse and reassembled. Dryer works like a champ again.

Dryer stopped working completely

  • Customer: Mary from Norwalk, AL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Diagnosed the problem on parts select, ordered the part and watched the youtube video on how to install and done! Super easy - thanks for boosting my "chicks can fix anything" mojo and saving me a bunch of $$.

No heat, took a while to diagnose

  • Customer: Matt from Newark, DE
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
Saw no heat, web said probably the fuse. Replaced the fuse. Nope. Second guess was the thermostat at the exhaust. Replaced that. Nope. Finally got to actively troubleshooting and isolated one of the thermostats near the heating element. Replaced that and everything is fine. So now I have a good spare fuse and thermostat for the next repair. There was one tool I wished I had, a socket small enough to open the back. I had to use pliers and that was a pain. Other than that the repair was almost trivial, just unplug the bad one and plug in the good one.

no heat

  • Customer: Joseph from Pembroke Pines, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
The repair was really simple and easy. This is because of the customer support I got from the company. Everything on the Video-Tutorial on how to install the part/s is a kind of valuable help to anybody who will try to be a do-it-yourself passion.Thank you guys.

Dryer Would Run But Not Heat.

  • Customer: David from Perry, OK
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
First I read about repair problems on this unit. Went to parts select help and read about my problem. I decided it could be the thermal fuse. When I took the vent off pipe off it had the starting of a birds nest in it. This plugging up the vent pipe caused over heating blowing the fuse. Thanks part select

dryer would not start

  • Customer: andrea from henderson, KY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
just removed old fuse and installed new one ..... cleaned all the vents out to

Dryer did not work

  • Customer: Charles from Avon, CT
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Went to your web site and found 40% of the time the thermal fuse is the problem. By using your site found how to locate fuse & test it. It took me 10 min to take out the old part & tested it to find it bad. I ordered the part which cost $10 & got it in 3 days. It took me 10 min to install it and the dryer is fine. This save me a big repair bill.

Unit didn't heat anymore.

  • Customer: Wolfram from Atlanta, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
As per online video instruction. Easy as pie...
All Instructions for the 11060857990
1,411-1,425 of 1,576