11060812990 Kenmore Dryer - Instructions

turn off elec./disconnect at recep.- remove vent pipe- remove back of dryer- remove each part and re-install new part- relaced thermal cut-off, thermostat, fuse, and heat element...time about 30 min. also vacuumed dryer and vent pipe-time less than 15 min.- parts arrived day after they were ordered.

First I watched Partselect's wonderful videos on what could cause the dryer from having to use multiple cycles to dry and the parts involved. I then took the back of the dryer off and tested all three parts with a multi-meter to determine which part had no resistance. The thermal fuse did not register any thing, so I ordered the part and a few days later put it in. The dryer dries in just one cycle saving on the cost of repair and electric bill. Partselect.com is my first go to sight for any repair. They make it so simple and comprehensive that any one can do the repair. I then used duct tape to make a secure connection to the duct pipe in order for it to properly vent to the outside.

Previously I had repaired two washing machines and now a dryer, which is why my mom nick named me Josephine. So ladies you can make the repairs as well.

should have bought and used a voltmeter first. replaced heating element and fuse and other thermostat before I got a voltmeter and realized it was the cycling thermostat that was bad. easy after that

I watched the PartSelect video once before the part arrived. Had the part replaced in under 15 minutes. Very quick and easy.

Remove the exhaust tubing connection and the back panel (five nut screws). Locate the fuse; it is just to the right of the lint trap shoot, midway between the top and bottom of the back panel area. Replacement is visually intuitive.

Went to YouTube It was real easy.

I ordered the part, watched the video and made the repair in less than thirty minutes. This was much cheaper than purchasing a new dryer.

Pull off the front panel of the dryer, and replaced the thermal fuse. Very easy. Plus, vacuumed out the whole inside of the dryer, the rear and the tube running from the dryer to the outside. Will be doing this at least every 3 months to be safe. You would be surprised at how much lint builds up inside the machine. Eve though we clean the filter trap after every use of a load of clothes.

Repair went fine. Really easy for the most part. Unfortunately it didn't solve my problem. Great place to get parts though. I'm going to continue my search for the source of the noise

Thank you for the the installation tip I received along with the part. The suggestion of removing the front panel to install the belt made the installation go very smoothly.

I followed the directions on your site. I pulled out the filter on the top of the machine. Then removed the two screws where the filter is located, I am not sure I would have found those screws had it not been for your directions. I then pulled up on the top of the machine by grabbing the sides near the front of the top, it came right up. I then raised it enough to place a broom handle to hold the top up so I could reach the switch. I removed the two screws holding the switch and then pulled the connector apart. I then replaced the switch with the two screws and plugged the connector back together. Removed the broom handle and closed the top and replaced the two screws I removed by the filter. Replaced the filter and started the machine running and opened the door and it turned off and the light came on. It took me about twenty minutes.

I unplugged the dryer then removed 2 Phillips screws from lint trap. Then I popped the top up on each top corner with a screwdriver. I removed the 2 screws holding the front cover. I unclipped the wiring connection and moved the panel. I took out the old belt, put the tensioned back on then put the new belt around the drum and held the drum up with my shoulder then put the belt through the tensioner and put it on the motor spindle by pushing the tensioner back. I put it back together and it worked perfectly. Your video was very helpful. Job was very easy.

Had my wife call the repair man. Since it was Saturday afternoon, no luck. YouTube help me diagnose the problem. I found that the drum belt slipped off the idler pulley assembly and the assembly was laying on the floor. I noticed that the belt was frayed and was probably stretched out which may be why the belt slipped off in the first place. I glued the frayed pieces of the belt back with gorilla glue and clamps. You Tube helped me mount the idler pulley assembly and string the belt correctly. I then ordered the replacement parts through your website. The parts came to my home in a few days and I will fix the dryer properly when I get a chance.

The instruction sheet that comes with the parts is excellent. Follow it and all goes well. Be patient and stay away from the sharp sheet metal edges present in all such appliances !!

First bought the Cycling Thermostat and Thermal Fuse. Installed. Still did not work.Next bought the Thermal Cut-Off Switch and the High Limit Thermostat. Installed. Still did not work. Then purchased the timer and installed. Still did not work. Finally tested the heat element with an on/off switch and wire. The heater worked. Changed the 2-pole 30 amp switch in panel box and the problem was solved. The parts were reasonable and easy to install. I left the new parts in and saved the old oned for the future, Parts delivery was quick. Will use parts Select in the future.