Models > 11060722990 > Instructions

11060722990 Kenmore Dryer - Instructions

All installation instructions for 11060722990 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11060722990
1,771-1,785 of 1,919
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

no heat no igniter lite no gas flow

  • Customer: Douglas from Saginaw, MI
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
replaced thermo fuse. not the problem. not sure how to test for next step. timer, cycler tumbler all work just won't fire up.

dryer did not work

  • Customer: Donald from Campbell, NY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
unplugged unit, removed the back panel replace thermo fuse and replace back panel, plugged electric cord back in and we were back in business. real easy fixx

unit wouldn't light

  • Customer: mark from burbank, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
bought thermal fuse and thermostat as most likely. Took apart and checked with voltmeter and found the fuse open. Replaced it. Video instructions are helpful as is the part location in the drawings. Real problem was lint had built up in back vent area, blocking cooling/ burner intake air. Went through entire dryer and vacuumed it out

The control panel won't leave Casual load.

  • Customer: Ann from Cincinnati, OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Well the video showed us taking off the back. Which wouldn't come off. Welded. Then we could not find the fuse in back of the unit or bottom. The second time we tried we found it in the front. We had to take off the front, bottom cover then we found the fuse. But, it didn't fix the problem. The unit is still on Casual load only. When we push the buttons the other lights light up but goes back to Casual. The unit is clear of lint and still drys but only at the Casual setting.

Gas burner would not fire.

  • Customer: Leif from Plainfield, IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
First removed and checked the ignighter. It was fine. Next I located the schematic drawing and discovered that the burner, ignighter, and flame detector were all operated by one simple 110 volt circuit. This circuit did not power up when the dryer was cycled on. I pulled the dryer from the wall, removed the back panel, the vent etc. I then located the operating thermostat and the thermal fuze. The thermal fuze was open. (GOOD NEWS AN EASY FIX!!!) Thanks Guys

Dryer would not run or start at all. Seemed like it had no power but the light still worked and it wasn't the breaker.

  • Customer: Joshua from Sturgeon Bay, WI
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Took 12 screws off the back. One screw for the fuse. $9.32 and 30 minutes and we're back in business!

the lint chute assembly had corroded & would not accept the lint screen.

  • Customer: Richard from Paramount, CA
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
I pulled thee dryer out from the wall, shut off the gas & disconnected the gas line & the air vent, I then removed the fasteners from the upper end of the lint chute assembly (accessible from the top of the machine). I then tipped the machine over on to its front side making the back fully accessible. After removing the back cover, I removed the remaining fasteners holding the lint chute assembly in place & removed the part. I then removed the assembly only to find that the seals were not included in the package even though I had specifically asked about the seal when I called in & place my order. The response to my question was " seals are included that is why it is called an assembly." The end result was that I had to use alternate material & fabricate my own seals in order to complete the installation. As a result a repair which should have taken no more that 30 minutes, took over two hours.

Drum seal came apart

  • Customer: Glen from El Paso, TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Raised top of dryer and removed screws holing front on. slid front panel up and off to remove drum. Seal was easy to install but you do have to be careful with the adhesive. After adhesive was dry laid dryer on it's back and installed drum. Reinstalled drum belt. Placed front panel back on and installed the two screws holding it in place. Set dryer upright and closed top.

noise due to worn drum wheels

  • Customer: Derek from Wyoming, MI
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
fliped up top, removed 2 5/16 screws from face and removed. removed drum and belt. removed two piece ring bearing and removed front seal from front face. installed new seal and split bearing the way others were removed. reassembled dryer in reverse order.

Lint screen broken

  • Customer: Peggy from Kingsbury, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Open box, insert lint screen!

old lint filter was broken

  • Customer: John from York, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
All I had to do was take out the broken filter and replace it with the new one. It fit perfectly. The replacement took less than 5 minutes. I should have done it a year ago!!

Broken part

  • Customer: Cassandra from Chicago, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Replaced the part. It just slid right in to the appropriate space on the dryer.

The clip that holds the plastic handle to the lint screen broke off.

  • Customer: Pat from Zebulon, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The new lint screen fit perfectly. All I had to do was slip it in the lint filter slot.

Lint filter was broken

  • Customer: Calvin from Saco, ME
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Tried to replace filter would not fit It was delivered outside and was real cold and stiff after I let it set for awhile it warmed up it fit great. Thank you Calvin

old filter broke

  • Customer: Ellen from Burlington, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
took out old put in new
All Instructions for the 11060722990
1,771-1,785 of 1,919